# AEM wideband issue, what am I doing wrong?

**URL:** https://forums.speedlife.net/t/aem-wideband-issue-what-am-i-doing-wrong/210330
**Category:** SON240sx Automotive
**Created:** [March 21, 2011, 7:39pm UTC](https://forums.speedlife.net/t/aem-wideband-issue-what-am-i-doing-wrong/210330 "2011-03-21T19:39:16Z")
**Posts on this page:** 10
**Page:** 1

<div class="post-metadata">

### Author: ![prozac3ne2nr](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/prozac3ne2nr/32/5581_2.png) [@prozac3ne2nr](https://forums.speedlife.net/u/prozac3ne2nr)
#### Post date: [March 21, 2011, 7:39pm UTC](https://forums.speedlife.net/t/aem-wideband-issue-what-am-i-doing-wrong/210330/1 "2011-03-21T19:39:16Z")

</div>

Installed a new AEM wideband and sensor on the weekend. The issue is after letting go of the gas say on the hihgway or slower roads the gauge gets the horizontal line reading (no input?) until I hit the accelerator again  
It’s as if it hits maximum lean or no gases to measure, but that’s not possible because the car is running and idle is fine as well as neutral decelartion.  
It starts up fine and settles down on idle and all through boost holds it value but +/-.2 v.

Sensor was installed on the downpipe at more than the minimum 10Deg angle. I thought I was getting a sketch input voltage from the switched source but getting a better source didn’t help.  
Screw on the back of gauge is in the P0 position.

any input and ideas will be welcomed.  
Zac

---

<div class="post-metadata">

### Author: ![sharpe\_corners](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/sharpe_corners/32/5767_2.png) [@sharpe\_corners](https://forums.speedlife.net/u/sharpe_corners)
#### Post date: [March 21, 2011, 7:51pm UTC](https://forums.speedlife.net/t/aem-wideband-issue-what-am-i-doing-wrong/210330/2 "2011-03-21T19:51:16Z")

</div>

Redo your ground.

Those stupid aem’s require a retardedly good ground to work well, when most others a normal one will suffice.

---

<div class="post-metadata">

### Author: ![face](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/face/32/5504_2.png) [@face](https://forums.speedlife.net/u/face)
#### Post date: [March 21, 2011, 8:38pm UTC](https://forums.speedlife.net/t/aem-wideband-issue-what-am-i-doing-wrong/210330/3 "2011-03-21T20:38:32Z")

</div>

Never had a wideband before? This is normal operation. During closed throttle deceleration, fuel isn’t required, so typically the injectors do not operate, thus giving you a lean (—) reading.

---

<div class="post-metadata">

### Author: ![prozac3ne2nr](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/prozac3ne2nr/32/5581_2.png) [@prozac3ne2nr](https://forums.speedlife.net/u/prozac3ne2nr)
#### Post date: [March 21, 2011, 8:45pm UTC](https://forums.speedlife.net/t/aem-wideband-issue-what-am-i-doing-wrong/210330/4 "2011-03-21T20:45:50Z")

</div>

Dylan I’ll reground, thx.

Nope first Wideband but injectors will still pulse as long as the engine rotates, CAS singnals right? But I’ll research some more on what you said because it does lean out hard before going to (—).  
thx face.

---

<div class="post-metadata">

### Author: ![Wongger](https://avatars.discourse-cdn.com/v4/letter/w/41988e/32.png) [@Wongger](https://forums.speedlife.net/u/Wongger)
#### Post date: [March 21, 2011, 8:56pm UTC](https://forums.speedlife.net/t/aem-wideband-issue-what-am-i-doing-wrong/210330/5 "2011-03-21T20:56:43Z")

</div>

On my AEM wideband whenever I stop giving it gas it goes (—) for a few seconds, then back to my proper idle. I thought that was the usual also

---

<div class="post-metadata">

### Author: ![240sx\_nismo](https://avatars.discourse-cdn.com/v4/letter/2/3da27b/32.png) [@240sx\_nismo](https://forums.speedlife.net/u/240sx_nismo)
#### Post date: [March 21, 2011, 9:39pm UTC](https://forums.speedlife.net/t/aem-wideband-issue-what-am-i-doing-wrong/210330/6 "2011-03-21T21:39:25Z")

</div>

mine dose same thing, brand new and just installed by a pro, my buddies dose the same as well.

---

<div class="post-metadata">

### Author: ![sonfc](https://avatars.discourse-cdn.com/v4/letter/s/a88e57/32.png) [@sonfc](https://forums.speedlife.net/u/sonfc)
#### Post date: [March 21, 2011, 10:46pm UTC](https://forums.speedlife.net/t/aem-wideband-issue-what-am-i-doing-wrong/210330/7 "2011-03-21T22:46:50Z")

</div>

No your injectors turn off when you have your foot off the pedal or are decelerating, its supposed to do that

---

<div class="post-metadata">

### Author: ![prozac3ne2nr](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/prozac3ne2nr/32/5581_2.png) [@prozac3ne2nr](https://forums.speedlife.net/u/prozac3ne2nr)
#### Post date: [March 22, 2011, 5:05am UTC](https://forums.speedlife.net/t/aem-wideband-issue-what-am-i-doing-wrong/210330/8 "2011-03-22T05:05:12Z")

</div>

Got ya. Ok thanks for all the input. You guys are right and that is normal operation. The LC1 just shows 21 instead of —

---

<div class="post-metadata">

### Author: ![Philly](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/philly/32/5748_2.png) [@Philly](https://forums.speedlife.net/u/Philly)
#### Post date: [March 22, 2011, 5:05am UTC](https://forums.speedlife.net/t/aem-wideband-issue-what-am-i-doing-wrong/210330/9 "2011-03-22T05:05:18Z")

</div>

Mine does the same thing zac. Installed by Riyad too.

---

<div class="post-metadata">

### Author: ![prozac3ne2nr](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/prozac3ne2nr/32/5581_2.png) [@prozac3ne2nr](https://forums.speedlife.net/u/prozac3ne2nr)
#### Post date: [March 22, 2011, 6:32am UTC](https://forums.speedlife.net/t/aem-wideband-issue-what-am-i-doing-wrong/210330/10 "2011-03-22T06:32:31Z")

</div>

Thanks Phil. Oh well, just a minor inconvenience I guess.
