# Budget build. $4K = 10's **URL:** \ **Category:** Builds\ **Created:** [July 25, 2011, 6:55pm UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614 "2011-07-25T18:55:13Z")\ **Posts on this page:** 20\ **Page:** 6
**Author:** ![jdaniels](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/jdaniels/32/6399_2.png) [@jdaniels](https://forums.speedlife.net/u/jdaniels)\ **Post date:** [July 28, 2011, 7:45pm UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/101 "2011-07-28T19:45:12Z")
You’ll see, we’re going to make this shit go retarded fast for retarded cheap. License plate is BYE ZR1. ---
**Author:** ![KrazyKid](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/krazykid/32/6371_2.png) [@KrazyKid](https://forums.speedlife.net/u/KrazyKid)\ **Post date:** [July 29, 2011, 6:55am UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/102 "2011-07-29T06:55:18Z")
9" gears are cheaper by like $30 over the 8.8. But you will spend more than that adapting disk brakes. Its crazy strong, but also way heavier than the 8.8. (I am adding 75lbs with the iron block, so the 9" will add 35lbs over the 8.8, and I bet the 8.8 is heavier than the stock GM axle) 100lbs just took a .10 off my et. every little bit counts on this build. Its a tight rope walk, quality, functionality and $ wise. I can get an 8.8 full axle, from an explorer for $100-150 from a yard, last one I got for free because the dude didn’t want to look at it in his back yard at his house anymore! Specs are: 59.5" wide, with a 2" offset. Stock 31 spline axles shafts are $50 from a yard, if that. I got 2 longs and 2 shorts for free from an off road guy who just didnt want them anymore either. Ford Racing R&P set is $185 shipped. Got a auburn full spool on ebay for $95 shipped. Rebuild kit with bearings, seals, shims, etc. $60 shipped. Work to build it: Dump the fluid, pull the long side C-clip and remove the axle shaft. Cut the tube somewhere in the middle, doesn’t really matter where, doesn’t even need to be perfectly square. Take the half of the tube with the brake hub, toss it in the band saw, chop 2" off it. Again square is nice, but not really needed. Bevel both cuts. Measure the inside DIA of the axle tubes. Go to the metal store and get tube that has the same OUTSIDE dia as the inside dia on the tubes. Turns out metal supermarket has the EXACT size needed. OR if you are handy and anal about fitment, get a slightly larger outside dia, and turn it down on a lathe. Cut the tube about 8 inches long… no less. longer is better but totally un needed. Now the axle tube is a welded seam tube, so you need to take an angle grinder and just grind a decent valley down the side, straight, on the 8" tube you have above. Pound that bitch into the axle tube on the 8.8… the valley is so the weld seam doesn’t catch the sleeve and bind it, totally fucking you. Use a block of wood, so you dont mushroom over the other end of the sleeve tube. heck bevel both of them too to help slide in. hammer it in half way, 4 inches. Now line up the short side tube you cut the 2" off, with the inside weld seam VS the valley you ground into the inner sleeve… that will keep the caliper mount facing the right way! IDIOT PROOF RIGHT! hammer that bitch back on now… as you get close to meeting the 2 8.8 tubes again, start taking measurements to make sure you dont send it TOO FAR, or you are fucked. Also hope you measured right when you made the cuts on the tubes, and you cut enough out, or they will touch, bottom out and you are still too wide. FUCKED. Once its back together you are good to go. Put another short side axle shaft in the rear end, put the C-clip back on and get the TIG welder out. Tack 4 sides, alternating each one. The sleeve you hammered in will keep it aligned very well, the axle shaft, bearings and diff will also keep it aligned (that’s essentially what a real “axle jig” is doing). Pick the first tack weld and lay down about 3/4" of a bead. rotate it and pick the opposit tack, lay a bead. rotate, bead… etc. every time spin the axles to make sure its not binding. Let it cool in between if you want too… just take your time. Both axles I did this way, the side I shortened actually spin BETTER than the oem side! dead nuts straight. Nothing fancy, no brain surgery work. $490 paying max price on junkyard parts, new gears, new rebuild, used spool (add $80 for a new spool) and you have a built 8.8 57.5" wide, with disk brakes. :number1 > [@FS: World of Warcraft & expansion](https://forums.speedlife.net/t/fs-world-of-warcraft-expansion/44254/2): > > You can have 2 out of three of these, but you won’t have the other-cheap, fast, and reliable. Choose wisely:rofl If you are a boob! :rofl I am gunna do ALL THREE. MAKE MY WORD! ---
**Author:** ![KrazyKid](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/krazykid/32/6371_2.png) [@KrazyKid](https://forums.speedlife.net/u/KrazyKid)\ **Post date:** [July 29, 2011, 11:02am UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/103 "2011-07-29T11:02:21Z")
Updated OP with some $$$$$ figures. it will be CLOSE to the $4k mark. ---
**Author:** ![ErnGotti](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/erngotti/32/6372_2.png) [@ErnGotti](https://forums.speedlife.net/u/ErnGotti)\ **Post date:** [July 29, 2011, 3:55pm UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/104 "2011-07-29T15:55:02Z")
> [@FS: 2003 yamaha vstar](https://forums.speedlife.net/t/fs-2003-yamaha-vstar/34525/23): > > crossover u joint a precision 355 Napa Ujoint 355 comes in a SuperStrength Greasable version, P/N 290. $20.39+tax in stock 😉 ---
**Author:** ![KrazyKid](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/krazykid/32/6371_2.png) [@KrazyKid](https://forums.speedlife.net/u/KrazyKid)\ **Post date:** [August 1, 2011, 7:29am UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/105 "2011-08-01T07:29:10Z")
werd. When i get crackin on this thing, I hope I can build motor mounts and get the rear end in the car so I can reuse the stock driveshaft and that U joint. That way I can also just order/find an upgraded stock replacement shaft, and not need one custom made. ---
**Author:** ![jdaniels](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/jdaniels/32/6399_2.png) [@jdaniels](https://forums.speedlife.net/u/jdaniels)\ **Post date:** [August 1, 2011, 7:37am UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/106 "2011-08-01T07:37:02Z")
Just need a TH400 yoke for the 4l80e. It would really be MUCH MUCH MUCH easier and things would work out a lot better (ex. Stock parts sourced, etc) if you get an LS1 subframe (OEM or aftermarket). ---
**Author:** ![KrazyKid](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/krazykid/32/6371_2.png) [@KrazyKid](https://forums.speedlife.net/u/KrazyKid)\ **Post date:** [August 2, 2011, 1:05pm UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/107 "2011-08-02T13:05:21Z")
[http://cgi.ebay.com/ebaymotors/95-Twin-Turbo-Twin-Aftercooled-Custom-Street-Camaro-/320735055721?pt=US\_Cars\_Trucks&hash=item4aad4c8f69](http://cgi.ebay.com/ebaymotors/95-Twin-Turbo-Twin-Aftercooled-Custom-Street-Camaro-/320735055721?pt=US_Cars_Trucks&hash=item4aad4c8f69) Fuck it I am just going to buy this gem. ---
**Author:** ![adamea1635](https://avatars.discourse-cdn.com/v4/letter/a/bc8723/32.png) [@adamea1635](https://forums.speedlife.net/u/adamea1635)\ **Post date:** [August 2, 2011, 1:59pm UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/108 "2011-08-02T13:59:47Z")
> [@eco-terrorests](https://forums.speedlife.net/t/eco-terrorests/44356/7): > > [http://cgi.ebay.com/ebaymotors/95-Twin-Turbo-Twin-Aftercooled-Custom-Street-Camaro-/320735055721?pt=US\_Cars\_Trucks&hash=item4aad4c8f69](http://cgi.ebay.com/ebaymotors/95-Twin-Turbo-Twin-Aftercooled-Custom-Street-Camaro-/320735055721?pt=US_Cars_Trucks&hash=item4aad4c8f69) > > Fuck it I am just going to buy this gem. Those are the worst set of pictures to show the car… Looks like Kit from night rider had an illegitimate son… ---
**Author:** ![toomanycamaros](https://avatars.discourse-cdn.com/v4/letter/t/7993a0/32.png) [@toomanycamaros](https://forums.speedlife.net/u/toomanycamaros)\ **Post date:** [August 5, 2011, 7:40pm UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/109 "2011-08-05T19:40:27Z")
Did you try cruising around LS1tech and other forums for a cheap used 9". I wound up about 500 bucks into the one in my car and it’s a full optioned moser unit that cost about 3k new. The deals are out there if you can find them. Or does that count as cheating the budget? ---
**Author:** ![KrazyKid](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/krazykid/32/6371_2.png) [@KrazyKid](https://forums.speedlife.net/u/KrazyKid)\ **Post date:** [August 8, 2011, 7:19am UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/110 "2011-08-08T07:19:16Z")
LOL no its not cheating. LS1tech for some reason is hit or miss, loading pages at work… my #1 means for R&D. lol ---
**Author:** ![SSmokinn\_SS](https://avatars.discourse-cdn.com/v4/letter/s/ec9cab/32.png) [@SSmokinn\_SS](https://forums.speedlife.net/u/SSmokinn_SS)\ **Post date:** [August 8, 2011, 4:08pm UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/111 "2011-08-08T16:08:27Z")
> [@Sabres vs Caps 3-5-08 HSBC Meet!](https://forums.speedlife.net/t/sabres-vs-caps-3-5-08-hsbc-meet/44464/7): > > LOL no its not cheating. LS1tech for some reason is hit or miss, loading pages at work… my #1 means for R&D. lol Just the other day there was a guy in the forsale part of ls1tech that was selling his moser 12 bolt with 4.11’s for $500 plus a stock 10 bolt. ---
**Author:** ![KrazyKid](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/krazykid/32/6371_2.png) [@KrazyKid](https://forums.speedlife.net/u/KrazyKid)\ **Post date:** [August 9, 2011, 6:05am UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/112 "2011-08-09T06:05:39Z")
> [@FS: 1986 BMW E30](https://forums.speedlife.net/t/fs-1986-bmw-e30/44444/12): > > Just the other day there was a guy in the forsale part of ls1tech that was selling his moser 12 bolt with 4.11’s for $500 plus a stock 10 bolt. from where? local/sorta local? fucking ls1tech hates my work proxy… its hit or miss loading pages. ---
**Author:** ![jdaniels](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/jdaniels/32/6399_2.png) [@jdaniels](https://forums.speedlife.net/u/jdaniels)\ **Post date:** [August 9, 2011, 6:42am UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/113 "2011-08-09T06:42:46Z")
I troll LS1tech on a 24/7 basis and I have yet to see this. ---
**Author:** ![ramairetransam](https://avatars.discourse-cdn.com/v4/letter/r/58956e/32.png) [@ramairetransam](https://forums.speedlife.net/u/ramairetransam)\ **Post date:** [August 9, 2011, 6:49am UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/114 "2011-08-09T06:49:09Z")
> [@957whp evo. bro lol](https://forums.speedlife.net/t/957whp-evo-bro-lol/44469/16): > > from where? local/sorta local? > > fucking ls1tech hates my work proxy… its hit or miss loading pages. i get the same thing here . ---
**Author:** ![KrazyKid](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/krazykid/32/6371_2.png) [@KrazyKid](https://forums.speedlife.net/u/KrazyKid)\ **Post date:** [August 9, 2011, 6:59am UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/115 "2011-08-09T06:59:46Z")
> [@UB Parking lots today...](https://forums.speedlife.net/t/ub-parking-lots-today/44474/31): > > i get the same thing here . you work for NYS too? ---
**Author:** ![ramairetransam](https://avatars.discourse-cdn.com/v4/letter/r/58956e/32.png) [@ramairetransam](https://forums.speedlife.net/u/ramairetransam)\ **Post date:** [August 9, 2011, 8:37am UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/116 "2011-08-09T08:37:00Z")
yes ---
**Author:** ![HANSTECH](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/hanstech/32/6445_2.png) [@HANSTECH](https://forums.speedlife.net/u/HANSTECH)\ **Post date:** [August 9, 2011, 8:44am UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/117 "2011-08-09T08:44:33Z")
work is far from what you do jeff… ---
**Author:** ![ramairetransam](https://avatars.discourse-cdn.com/v4/letter/r/58956e/32.png) [@ramairetransam](https://forums.speedlife.net/u/ramairetransam)\ **Post date:** [August 9, 2011, 8:55am UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/118 "2011-08-09T08:55:24Z")
u should talk henry … ---
**Author:** ![KrazyKid](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/krazykid/32/6371_2.png) [@KrazyKid](https://forums.speedlife.net/u/KrazyKid)\ **Post date:** [August 9, 2011, 9:03am UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/119 "2011-08-09T09:03:47Z")
> [@SOLD](https://forums.speedlife.net/t/sold/31406/6): > > yes Yeah this new 3rd party cloud based proxy shit SUCKKKS ---
**Author:** ![HANSTECH](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/hanstech/32/6445_2.png) [@HANSTECH](https://forums.speedlife.net/u/HANSTECH)\ **Post date:** [August 9, 2011, 11:17am UTC](https://forums.speedlife.net/t/budget-build-4k-10s/259614/120 "2011-08-09T11:17:42Z")
> [@alright so here is my story](https://forums.speedlife.net/t/alright-so-here-is-my-story/44312/52): > > u should talk henry … hey now! you saw me hustlin the other day…for once. lol [Previous page](https://forums.speedlife.net/t/budget-build-4k-10s/259614.md?page=5) [Next page](https://forums.speedlife.net/t/budget-build-4k-10s/259614.md?page=7)