# CF Hood Question.. **URL:** \ **Category:** NYSpeed Automotive\ **Created:** [December 22, 2007, 1:11pm UTC](https://forums.speedlife.net/t/cf-hood-question/40668 "2007-12-22T13:11:37Z")\ **Posts on this page:** 11\ **Page:** 1
**Author:** ![Bsp\_TC](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/bsp_tc/32/4998_2.png) [@Bsp\_TC](https://forums.speedlife.net/u/Bsp_TC)\ **Post date:** [December 22, 2007, 1:11pm UTC](https://forums.speedlife.net/t/cf-hood-question/40668/1 "2007-12-22T13:11:37Z")
For those with cf hoods… Did it come pre-drilled with the windshield washer nozzle holes? If not did you drill into the hood to place them, or did you route them else where and i guess people who drilled hood pins to…how did you go about drilling the hood. ---
**Author:** ![ryanmcell](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/ryanmcell/32/7510_2.png) [@ryanmcell](https://forums.speedlife.net/u/ryanmcell)\ **Post date:** [December 22, 2007, 2:50pm UTC](https://forums.speedlife.net/t/cf-hood-question/40668/2 "2007-12-22T14:50:10Z")
On my Eclipse my VIS came pre-drilled for washer nozzles. I had to drill out for the hood pins. Basically I don’t know what the drill bit is called specifically, it’s a small drill bit but it increases in increments, just go slow and it keeps gauging the hole bigger, somebody please chime in with the proper name. ---
**Author:** ![HAiRymONkEe](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/hairymonkee/32/5172_2.png) [@HAiRymONkEe](https://forums.speedlife.net/u/HAiRymONkEe)\ **Post date:** [December 22, 2007, 2:53pm UTC](https://forums.speedlife.net/t/cf-hood-question/40668/3 "2007-12-22T14:53:25Z")
^ a step bit? ---
**Author:** ![SoloIIscoob](https://avatars.discourse-cdn.com/v4/letter/s/35a633/32.png) [@SoloIIscoob](https://forums.speedlife.net/u/SoloIIscoob)\ **Post date:** [December 22, 2007, 2:59pm UTC](https://forums.speedlife.net/t/cf-hood-question/40668/4 "2007-12-22T14:59:14Z")
for hood pins… 1. install pin shaft in rad. support. and then put tape in the approximate location shaft will touch hood. 2. put grease on top of pin shaft, close hood on pin shafts to mark where it contacts hood/tape. 3. drill with tape/ on hood in the location the grease spot marked on the hood(make sure bit is perpendicular to hood) 4. you now have your holes for the hood pins. the seibon hood i received for my WRX did have holes for the washer nozzles, tho i had to modify the washer nozzle to fit the provided holes. ---
**Author:** ![ryanmcell](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/ryanmcell/32/7510_2.png) [@ryanmcell](https://forums.speedlife.net/u/ryanmcell)\ **Post date:** [December 22, 2007, 4:04pm UTC](https://forums.speedlife.net/t/cf-hood-question/40668/5 "2007-12-22T16:04:12Z")
> [@HAiRymONkEe](#): > > ^ a step bit? Thank you, I couldn’t think. ---
**Author:** ![Justin](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/justin/32/7459_2.png) [@Justin](https://forums.speedlife.net/u/Justin)\ **Post date:** [December 23, 2007, 3:45pm UTC](https://forums.speedlife.net/t/cf-hood-question/40668/6 "2007-12-23T15:45:00Z")
ViS\>\* although my washers do not go in the hood. I’m sure if they did ViS would have made them to fit. ---
**Author:** ![Bacon](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/bacon/32/7230_2.png) [@Bacon](https://forums.speedlife.net/u/Bacon)\ **Post date:** [December 23, 2007, 3:55pm UTC](https://forums.speedlife.net/t/cf-hood-question/40668/7 "2007-12-23T15:55:26Z")
I had to do minor modifications to the one on my car, but in most cases it’s usually predrilled. ---
**Author:** ![avs](https://avatars.discourse-cdn.com/v4/letter/a/f475e1/32.png) [@avs](https://forums.speedlife.net/u/avs)\ **Post date:** [December 24, 2007, 7:56pm UTC](https://forums.speedlife.net/t/cf-hood-question/40668/8 "2007-12-24T19:56:38Z")
This is the type of router bit you need for drilling composite. From Onsrud ![https://www.onsrud.com/oc/mydata/common/xDocs.nsf/0520a971a66adeffc12569ab003d8ce1/faa554d74a39fe3e862572db006a7857/xRichDesc1/0.83C8?OpenElement&FieldElemFormat=jpg](https://www.onsrud.com/oc/mydata/common/xDocs.nsf/0520a971a66adeffc12569ab003d8ce1/faa554d74a39fe3e862572db006a7857/xRichDesc1/0.83C8?OpenElement&FieldElemFormat=jpg) ---
**Author:** ![cky89](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/cky89/32/4945_2.png) [@cky89](https://forums.speedlife.net/u/cky89)\ **Post date:** [December 24, 2007, 8:17pm UTC](https://forums.speedlife.net/t/cf-hood-question/40668/9 "2007-12-24T20:17:59Z")
that looks like a regular drill bit to me :gotme: does taper bit=step bit? ---
**Author:** ![ultradriver10000](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/ultradriver10000/32/7397_2.png) [@ultradriver10000](https://forums.speedlife.net/u/ultradriver10000)\ **Post date:** [December 24, 2007, 8:32pm UTC](https://forums.speedlife.net/t/cf-hood-question/40668/10 "2007-12-24T20:32:16Z")
use this ![http://www.m-99.co.uk/Air_Guns/Colt_COLT_357_PYTHON_MAGNUM_6/spkg62h.jpg](http://www.m-99.co.uk/Air_Guns/Colt_COLT_357_PYTHON_MAGNUM_6/spkg62h.jpg) ---
**Author:** ![cky89](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/cky89/32/4945_2.png) [@cky89](https://forums.speedlife.net/u/cky89)\ **Post date:** [December 24, 2007, 8:34pm UTC](https://forums.speedlife.net/t/cf-hood-question/40668/11 "2007-12-24T20:34:00Z")
> [@ultradriver10000](#): > > use this Just don’t use it to get your lug nuts off 🤣