# DIY: Two Toned Interior \*too many pics\* **URL:** \ **Category:** Builds\ **Created:** [May 9, 2006, 7:44pm UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836 "2006-05-09T19:44:20Z")\ **Posts on this page:** 20\ **Page:** 1
**Author:** ![LAFENGAS](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/lafengas/32/7573_2.png) [@LAFENGAS](https://forums.speedlife.net/u/LAFENGAS)\ **Post date:** [May 9, 2006, 7:44pm UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/1 "2006-05-09T19:44:20Z")
This was a tough decision for me, mainly becaues blue was a lot more ‘vibrant’ than my current color scheme of black, steel grey, and silver. Also two-tone interiors tend to be very ‘flashy’ and i wanted it to be much more on the subtle side. The material i used is Alcantara. Alcantara is different from ultra suede, though they are very similar, Alcantara is thicker and more durable. I ordered this from the UK from the supplier of Ferrari. I wrote this DIY for a BMW forum, so the disassembly/assembly doesn’t pretain to most vehicles, but the actual process of changing the fabric is pretty generic \*\*\*\*\*DIY as typed for the BMW forums \*\*\*\*\*\*\*\*\*\*\*\*\*\* For those who wish to two-tone their own interior using their own material. I have composed the following DIY and tried breaking it down as simple as I can. Depending on how anal you are, the project shouldn’t take more then a weekend. The following will assume you know how to remove your door panels from the car. There are seperate DIY’s showing how to remove the panels from the car. The following tools will help: - Aprox. 2 yards of fabric/material - Scissors - Contact Cement - Drill w/ 1/2" drill bit - Torex 20 bit - Razor knife - Energy Drink - Mineral Spirits Scissors: ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_A.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_A.JPG) Contact Cement (and brush). If you choose this brand of contact cement, make sure it’s the red can, not the green can. The green can is environmentaly friendly… and i hate the environment. Also, the green can doesn’t stick well at all. ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_B.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_B.JPG) Drill and a 1/2" drill bit (or slightly larger) ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_C.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_C.JPG) A torex 20 bit ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_D.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_D.JPG) Clamps and some padding. The padding will help distribute the weight so you don’t get creases in the fabric while the adhesive dries. ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_E.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_E.JPG) Razor knife ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_F.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_F.JPG) Energy Drink: ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_G.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_G.JPG) Mineral Spirits for and adhesive clean up, don’t confuse with the energy drink. ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_H.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_H.JPG) **I.) Disassemble the inner panel from the outter panel.** ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_00.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_00.JPG) 1.) Use a Torex 20 bit to unscrew the 8 screws from the backside holding the armrest in place 2.) These screws are marked with RED CIRCLES in the **picture above** close up of the torex screws: ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_01.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_01.JPG) 3.) Once the screws are removed, the armrest should just pop off. 4.) The PINK ARROWS show where 4 nuts are located that hold the air bag panel in place if the air bag is deployed during an accident. Simply unscrew these 4 nuts. You can do it by hand or with a 10mm socket 5.) The GREEN CIRCLES on the **above picture** indicate plastic rivits that have been melted to mount the panels together. Using the 1/2" drill bit, drill out the melted portion. All you are doing is removing the plastic that’s melted. Remove as little as possible, you will be using the remaining plastic to reassemble the panels. Drill out as little as possible to release the hold. Drilling the plastic rivits: ![http://ubrf.ddetail.com/lafengas/interior_DIY/interior_panel06.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/interior_panel06.JPG) ![http://ubrf.ddetail.com/lafengas/interior_DIY/interior_panel07.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/interior_panel07.JPG) Once all the rivits have been drilled out and the armrest removed, you should be able to pop the center panel section out. You may find that you need to re-drill some of the rivits to free the panel completely. ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_03.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_03.JPG) **II.) Preparing the panel to be covered with fabric** 1.) Clean/degrease the panel with soap and water on a towel. This will help to remove any Armor-All or anything else that will prevent the adhesive from working properly. 2.) Place the panel on top of your fabric and cut the fabric to the apox. shape/size. Try to cut atleast 2" larger all the way around the panel. This will give you room for error and enough material to wrap around to the backside of the panel. ![http://ubrf.ddetail.com/lafengas/interior_DIY/interior_panel13.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/interior_panel13.JPG) **III.) Bonding the fabric to the panel** 3.) Now time for the adhesive. It’s very important to do only the larger flat, centeral sections first. For larger panels (the doors) I broke the process into 3 different time periods. By doing this, you allow the fabric to fully adhere and setup so you don’t shift the material around too much over a large area. This keeps the material from sliding all over and preventing wrinkles or a poor bond. ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_04.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_04.JPG) Put a fair amount of contact cement directly on the leather and spread it around to get nice thick, even coat. Let the adhesive set for a several minutes until it has formed a gel-like consistancy.(like boogers during a mild flue). You may have to do a few layers of adhesive. By doing this, the adhesive won’t bleed through the fabric, causing more issues. If you wait too long, it won’t bond well with the fabric. Expierment on a scrap piece of material to figure out your time period. Wait until these areas are fully bonded/cured (15mins - 20mins) before you move on to the next section so you don’t get wrinkles from shifting material. The picture below shows an example of the first section I did (about 1/3 of the total area). I placed the fabric on this and pressed firmly all over until the adhesive set (aprox 15 minutes) and form a good bond. ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_05.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_05.JPG) Repeat this until you get the majority of the panel’s flat areas bonded. Try to place the fabric so it falls natural, if you’re stretching it to get it to fit… the fabric will likely wrinkle later on. Once you complete the main areas, cut holes and ‘relief slits’ in the fabric so you can from the fabric into the tighter cornered areas. Cut away the material to clear holes for armrest and screws. Remove as little fabric as possible so you have enough to fill the voids once the fabric has formed. The picture below shows the upper armrest mount. ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_06.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_06.JPG) this pic shows a reference to where you cut the slits and openings in comparison to the panel: ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_08.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_08.JPG) Once you cut the material, place some more adhesive between the panel and the fabric where the armrest compresses the fabric. Don’t forget to let the adhesive tack up. Then bolt the armrest on nice and tight and throw the little “airbag” labeled piece in as well. This will pull the fabric into place. ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_09.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_09.JPG) Once you have the armrest in place and tightened down, leave it on. By leaving it on, you won’t get any surprises when you go to bolt the armrest back in place. If you pull the fabric tight around all the corners to the backside of the panel, then bolt on the armrests afterwards…that may pull the fabric and screw up all the work you’ve done. So leave the armrests on. ---
**Author:** ![LAFENGAS](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/lafengas/32/7573_2.png) [@LAFENGAS](https://forums.speedlife.net/u/LAFENGAS)\ **Post date:** [May 9, 2006, 7:44pm UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/2 "2006-05-09T19:44:37Z")
**IV.) wrapping the tighter areas** For the center gap, where the airbag panel is located, cut relief slits in the fabric to make it easier to wrap. I marked the picture with red areas showing where the factory had cut the leather, i recommend cutting it like this. ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_10.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_10.JPG) Put adhesive on a small section and wait for it to gel up. When the adhesive is ready, wrap the fabric and hold it in place. **TIP** _Consume Energy Beverage now… holding the material in place waiting for glue to dry isn’t exciting._ Again, to show relief cuts, this is where the panel fits around the speaker. ![http://ubrf.ddetail.com/lafengas/interior_DIY/interior_panel15.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/interior_panel15.JPG) and held in place with tape: ![http://ubrf.ddetail.com/lafengas/interior_DIY/interior_panel16.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/interior_panel16.JPG) **TIP** For the really tight inner corner for the airbag section: Ball up a piece of towel and fit it into the corner, then tape it in place. Holding this tight with your hands for 15mins will be sure to cramp them. ![http://ubrf.ddetail.com/lafengas/interior_DIY/interior_panel17.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/interior_panel17.JPG) ![http://ubrf.ddetail.com/lafengas/interior_DIY/interior_panel18.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/interior_panel18.JPG) This next pic shows the straight edges. Do a small section at a time, you may need to sit with it and hold it while the adhesive sets up and bonds. Do as much as you can hold with your hands or more if you have tape/clamps to take your place. ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_11.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_11.JPG) Once everything has had a chance to cure and fully bond. ( I recommend waiting until all the edges have been done and had a couple hours to fully cure) Cut the access material with a knife or scissors ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_12.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_12.JPG) **TIP:** For sharp corners, wrap the fabric around and orientate it in a way that it shows the least amount of wrinkles, then hold it in place with a piece of tape. Try using packaging tape, Duct tape will leave an adhesive residue behind and masking tape doesn’t stick well. ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_13.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_13.JPG) ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_21.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_21.JPG) Once everything has had a chance to cure, remove the armrests. You can see here how well the fabric has formed to the tight spots: ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_19.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_19.JPG) Your piece should look like this when you are done with the fabric part: ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_15.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_15.JPG) Once you have secured the 2 panels back together, you’re all set. If any adhesive is visible, use the Mineral Spirits to clean up your work. That’s it, Voila… you’re done :thanks: ![http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_20.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/DIY/DIY_20.JPG) ---
**Author:** ![LAFENGAS](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/lafengas/32/7573_2.png) [@LAFENGAS](https://forums.speedlife.net/u/LAFENGAS)\ **Post date:** [May 9, 2006, 7:47pm UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/3 "2006-05-09T19:47:41Z")
completed, installed and painted the titanium trim gloss black (BMW Black Saphire Metallic , to be exact) ![http://ubrf.ddetail.com/lafengas/interior_DIY/interior_install.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/interior_install.JPG) ![http://ubrf.ddetail.com/lafengas/interior_DIY/interior_install2.JPG](http://ubrf.ddetail.com/lafengas/interior_DIY/interior_install2.JPG) ---
**Author:** ![Nikuk](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/nikuk/32/7254_2.png) [@Nikuk](https://forums.speedlife.net/u/Nikuk)\ **Post date:** [May 9, 2006, 7:59pm UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/4 "2006-05-09T19:59:20Z")
Seriously… where do You get the time? As always (it seems) good work. Looked aweful well done in real life as well. Oh, and thank You for shopping at Ed Youngs! ---
**Author:** ![Paulo](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/paulo/32/7328_2.png) [@Paulo](https://forums.speedlife.net/u/Paulo)\ **Post date:** [May 10, 2006, 11:33pm UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/5 "2006-05-10T23:33:19Z")
y aren’t ur posts stickys? there should be a how-to list on this site when people do nice write-ups such as this one. good work man. for smaller panels i’ve used hot glue guns to hold it on the back cuz it dries alot faster. but what ur doin turned out awesome. ---
**Author:** ![walter](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/walter/32/7202_2.png) [@walter](https://forums.speedlife.net/u/walter)\ **Post date:** [May 11, 2006, 3:23pm UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/6 "2006-05-11T15:23:02Z")
I… hate… you… awesome, per usual ---
**Author:** ![RuBiCaNT](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/rubicant/32/7622_2.png) [@RuBiCaNT](https://forums.speedlife.net/u/RuBiCaNT)\ **Post date:** [May 11, 2006, 3:27pm UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/7 "2006-05-11T15:27:00Z")
Nicely done as usually Josh. Mucho Impressto. :tup: I can see it now, “LAFENGAS MY RIDE, Next on MTV69” ---
**Author:** ![2TurboZ](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/2turboz/32/7577_2.png) [@2TurboZ](https://forums.speedlife.net/u/2TurboZ)\ **Post date:** [May 11, 2006, 4:01pm UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/8 "2006-05-11T16:01:06Z")
:bowdown: ---
**Author:** ![Jskrapper](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/jskrapper/32/7570_2.png) [@Jskrapper](https://forums.speedlife.net/u/Jskrapper)\ **Post date:** [May 11, 2006, 4:09pm UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/9 "2006-05-11T16:09:42Z")
very nice work! ---
**Author:** ![MikeRi24](https://avatars.discourse-cdn.com/v4/letter/m/57b2e6/32.png) [@MikeRi24](https://forums.speedlife.net/u/MikeRi24)\ **Post date:** [May 11, 2006, 7:30pm UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/10 "2006-05-11T19:30:03Z")
ocne again, absolutely amazing! ---
**Author:** ![Daddie](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/daddie/32/7621_2.png) [@Daddie](https://forums.speedlife.net/u/Daddie)\ **Post date:** [May 12, 2006, 7:55am UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/11 "2006-05-12T07:55:15Z")
MTV Real Life : I can’t stop fucking with my car and never will You are the man. ---
**Author:** ![copperlegend](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/copperlegend/32/7445_2.png) [@copperlegend](https://forums.speedlife.net/u/copperlegend)\ **Post date:** [May 12, 2006, 8:10am UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/12 "2006-05-12T08:10:18Z")
wow that looks great! ---
**Author:** ![duck](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/duck/32/7183_2.png) [@duck](https://forums.speedlife.net/u/duck)\ **Post date:** [May 12, 2006, 8:13am UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/13 "2006-05-12T08:13:30Z")
fantastic writeup. well done mod to boot ---
**Author:** ![blueaccord](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/blueaccord/32/7431_2.png) [@blueaccord](https://forums.speedlife.net/u/blueaccord)\ **Post date:** [May 12, 2006, 8:17am UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/14 "2006-05-12T08:17:21Z")
Post a full pic of your car i want to see this with the wheels …Amazing job dude! ---
**Author:** ![JaysGreenLX](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/jaysgreenlx/32/7321_2.png) [@JaysGreenLX](https://forums.speedlife.net/u/JaysGreenLX)\ **Post date:** [May 12, 2006, 9:07am UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/15 "2006-05-12T09:07:10Z")
hahahahaha “Lafengas My Ride” I think there is potential. ---
**Author:** ![98SS10](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/98ss10/32/7288_2.png) [@98SS10](https://forums.speedlife.net/u/98SS10)\ **Post date:** [June 18, 2006, 6:57pm UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/16 "2006-06-18T18:57:01Z")
WTF happened to PICS??! ---
**Author:** ![Darksyde](https://avatars.discourse-cdn.com/v4/letter/d/ed655f/32.png) [@Darksyde](https://forums.speedlife.net/u/Darksyde)\ **Post date:** [June 18, 2006, 7:48pm UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/17 "2006-06-18T19:48:00Z")
> [@98SS10](#): > > WTF happened to PICS??! x2 ---
**Author:** ![Willybeen](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/willybeen/32/7351_2.png) [@Willybeen](https://forums.speedlife.net/u/Willybeen)\ **Post date:** [August 7, 2006, 5:27pm UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/18 "2006-08-07T17:27:30Z")
fix ur pics dambet ---
**Author:** ![Griff](https://avatars.discourse-cdn.com/v4/letter/g/f19dbf/32.png) [@Griff](https://forums.speedlife.net/u/Griff)\ **Post date:** [December 1, 2007, 4:10pm UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/19 "2007-12-01T16:10:30Z")
i can i bother you for a rehost of pics?? ---
**Author:** ![97eclipse420a](https://avatars.discourse-cdn.com/v4/letter/9/96bed5/32.png) [@97eclipse420a](https://forums.speedlife.net/u/97eclipse420a)\ **Post date:** [December 1, 2007, 6:00pm UTC](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836/20 "2007-12-01T18:00:50Z")
[quote=“Willybeen,post:18,topic:11836"”] fix ur pics dambet [/quote] :word: [Next page](https://forums.speedlife.net/t/diy-two-toned-interior-too-many-pics/11836.md?page=2)