# F-body Pinion seal leak...What to do?

**URL:** <https://forums.speedlife.net/t/f-body-pinion-seal-leak-what-to-do/55927>\
**Category:** NYSpeed Automotive\
**Created:** [October 4, 2008, 7:47am UTC](https://forums.speedlife.net/t/f-body-pinion-seal-leak-what-to-do/55927 "2008-10-04T07:47:47Z")\
**Posts on this page:** 12\
**Page:** 2

<div class="post-metadata">

**Author:** ![HYBOOST](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/hyboost/32/5088_2.png) [@HYBOOST](https://forums.speedlife.net/u/HYBOOST)\
**Post date:** [October 31, 2008, 4:06pm UTC](https://forums.speedlife.net/t/f-body-pinion-seal-leak-what-to-do/55927/21 "2008-10-31T16:06:33Z")

</div>

Fix it if you see drips on the driveway. The only way a new seal will leak is if the yoke is grooved or you damage it during install. If it is you need to buy 1) a new yoke or 2) A yoke repair sleeve. You need to mark the nut & yoke. That way you don’t over tighten the nut, causing too much pinion bearing preload by crushing the crush sleeve to much… Really easy fix. A basic seal puller will get the old seal out. They make a tool for installing the new seal, but you don’t need it if your carefull. A leaking seal won’t cause whine unless you drive it a long time when really low on lube or if pinion bearing is way too loose. If it’s a lack of lube causing problem, chances are the damage is done & you might need to replace the pinion bearings & races. PM me with any questions or torque specs.

---

<div class="post-metadata">

**Author:** ![E.Roy](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/e.roy/32/5073_2.png) [@E.Roy](https://forums.speedlife.net/u/E.Roy)\
**Post date:** [February 5, 2009, 11:33am UTC](https://forums.speedlife.net/t/f-body-pinion-seal-leak-what-to-do/55927/22 "2009-02-05T11:33:35Z")

</div>

> [@Z3Rick](#):
>
> I was the on-site rep for American Axle (supplier for the f-body rear axle) at the f-body assembly plant in St. Therese, Quebec, for the last 5 years of production. The pinion seal used in the last generation f-body was a triple lip seal that did weep a small amount of lube over time…The proper procedure would be to drain the old lube, flush the inside of the center section with brake cleaner and dry, then refill with proper amount of 90W gear lube and 1 oz. of the friction modifier.

The other problem I had was the Torsen diff (99-02?) wasn’t working very well. When I drained the fluid, it seemed very thin. So I replaced it with one qt 85w-90 conventional & 1qt Royal Purple syn w/friction additive in it (since I had it in the garage already). This helped and now the Torsen is working better. Apparently the last owner used only Royal Purple w/ add. and may have still put more fric. mod. in also, which probably contributed to the fluid weeping out.

Rick, your procedure is the right way to do it, and the way I will do it when I change it again in the spring time.

The friction modifier **_reduces_** the grip of the Torsen, so if anyone adds twice the amount, and thinks it will increase grip you would be mistaken. Follow what Rick said, and it will hook up.

IMO, don’t use royal purple

---

<div class="post-metadata">

**Author:** ![jt76](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/jt76/32/5100_2.png) [@jt76](https://forums.speedlife.net/u/jt76)\
**Post date:** [February 5, 2009, 12:37pm UTC](https://forums.speedlife.net/t/f-body-pinion-seal-leak-what-to-do/55927/23 "2009-02-05T12:37:14Z")

</div>

Moser 12 bolt :tup:

---

<div class="post-metadata">

**Author:** ![Firehawk853](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/firehawk853/32/7607_2.png) [@Firehawk853](https://forums.speedlife.net/u/Firehawk853)\
**Post date:** [February 5, 2009, 12:52pm UTC](https://forums.speedlife.net/t/f-body-pinion-seal-leak-what-to-do/55927/24 "2009-02-05T12:52:28Z")

</div>

> [@Shockwave179](#):
>
> :word:
> 
> Almost forgot to mention that, definitely don’t forget to use the gm friction modifier.

Friction modifier is only for clutch based posi units, ie Auburn & Eaton

> [@FlatBlak](#):
>
> The friction modifier **_reduces_** the grip of the Torsen, so if anyone adds twice the amount, and thinks it will increase grip you would be mistaken. Follow what Rick said, and it will hook up.
> 
> IMO, don’t use royal purple

Wrong, the Zexel Torsen is a worm gear posi unit much like the aftermarket Detroit TrueTrac. There is NO wearable friction material in these differentials. Therefore friction modifier in these is a waste of money and will make NO difference in how the diff functions

> [@jt76](#):
>
> Moser 12 bolt

Second that :tup:

---

<div class="post-metadata">

**Author:** ![lower\_the\_dynamite](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/lower_the_dynamite/32/7296_2.png) [@lower\_the\_dynamite](https://forums.speedlife.net/u/lower_the_dynamite)\
**Post date:** [February 5, 2009, 1:06pm UTC](https://forums.speedlife.net/t/f-body-pinion-seal-leak-what-to-do/55927/25 "2009-02-05T13:06:24Z")

</div>

> [@jt76](#):
>
> Moser 12 bolt :tup:

Third That. With a spool.

---

<div class="post-metadata">

**Author:** ![jt76](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/jt76/32/5100_2.png) [@jt76](https://forums.speedlife.net/u/jt76)\
**Post date:** [February 5, 2009, 1:09pm UTC](https://forums.speedlife.net/t/f-body-pinion-seal-leak-what-to-do/55927/26 "2009-02-05T13:09:44Z")

</div>

> [@lower\_the\_dynamite](#):
>
> Third That. With a spool.

meh, i had a spool… spools are gay… if you like driving the car.

Right now i have a Moser 9 inch with a tru trac and i couldn’t be happier.

---

<div class="post-metadata">

**Author:** ![Studderin](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/studderin/32/7197_2.png) [@Studderin](https://forums.speedlife.net/u/Studderin)\
**Post date:** [February 5, 2009, 1:46pm UTC](https://forums.speedlife.net/t/f-body-pinion-seal-leak-what-to-do/55927/27 "2009-02-05T13:46:19Z")

</div>

truetracs are cool, until you look at them after some hard miles. I really think there a low rpm unit, and a lot of people are going to be having problems with them.

---

<div class="post-metadata">

**Author:** ![lower\_the\_dynamite](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/lower_the_dynamite/32/7296_2.png) [@lower\_the\_dynamite](https://forums.speedlife.net/u/lower_the_dynamite)\
**Post date:** [February 5, 2009, 2:00pm UTC](https://forums.speedlife.net/t/f-body-pinion-seal-leak-what-to-do/55927/28 "2009-02-05T14:00:24Z")

</div>

> [@jt76](#):
>
> meh, i had a spool… spools are gay… if you like driving the car.
> 
> Right now i have a Moser 9 inch with a tru trac and i couldn’t be happier.

I drive my car everywhere. The only thing I don’t like about the spool is it sorta kills drag radials when turning. Besides that, it makes me slow down and never lets me drive it in the rain.

---

<div class="post-metadata">

**Author:** ![jt76](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/jt76/32/5100_2.png) [@jt76](https://forums.speedlife.net/u/jt76)\
**Post date:** [February 5, 2009, 2:10pm UTC](https://forums.speedlife.net/t/f-body-pinion-seal-leak-what-to-do/55927/29 "2009-02-05T14:10:06Z")

</div>

> [@Studderin](#):
>
> truetracs are cool, until you look at them after some hard miles. I really think there a low rpm unit, and a lot of people are going to be having problems with them.

Turbo and chuck seem to like theirs, and idk who is rougher on equipment

> [@lower\_the\_dynamite](#):
>
> I drive my car everywhere. The only thing I don’t like about the spool is it sorta kills drag radials when turning. Besides that, it makes me slow down and never lets me drive it in the rain.

Yeah dont i know it… i went through a set of BGF’s in 350 miles :picard:

---

<div class="post-metadata">

**Author:** ![LZ1](https://avatars.discourse-cdn.com/v4/letter/l/7ab992/32.png) [@LZ1](https://forums.speedlife.net/u/LZ1)\
**Post date:** [February 5, 2009, 2:50pm UTC](https://forums.speedlife.net/t/f-body-pinion-seal-leak-what-to-do/55927/30 "2009-02-05T14:50:01Z")

</div>

> [@jt76](#):
>
> Yeah dont i know it… i went through a set of BGF’s in 350 miles :picard:

Probably because you ran to much or to little tire psi…

---

<div class="post-metadata">

**Author:** ![Minglor](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/minglor/32/7373_2.png) [@Minglor](https://forums.speedlife.net/u/Minglor)\
**Post date:** [February 5, 2009, 2:58pm UTC](https://forums.speedlife.net/t/f-body-pinion-seal-leak-what-to-do/55927/31 "2009-02-05T14:58:11Z")

</div>

> [@ultradriver10000](#):
>
> Eric its a GM.
> 
> Rules for owning a GM product.
> 
> 1. Keep **some** oil in it. If possible change it once in a while, otherwise add as needed.
> 
> 2. Keep **some** coolant in it. If coolant is not available use some sort of liquid, I prefer beer. Oh and I know it doesn’t leak at all, so just stop worrying where it goes, the world may never know.
> 
> 3. Don’t worry about all the noises your car makes, it is just telling you it is ok. When it stops making noises that when you start to worry.
> 
> 4. Beat the snot out of it. GM didn’t build cars for girls, or guys that drive hondas, they build them for men, real men, iron workers. Don’t be a baby, do a burn out weekly to keep both you and your car happy.

I really should buy a F bod…hahaha

---

<div class="post-metadata">

**Author:** ![psychopjv](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/psychopjv/32/7251_2.png) [@psychopjv](https://forums.speedlife.net/u/psychopjv)\
**Post date:** [February 5, 2009, 5:00pm UTC](https://forums.speedlife.net/t/f-body-pinion-seal-leak-what-to-do/55927/32 "2009-02-05T17:00:16Z")

</div>

> [@LZ](#):
>
> Probably because you ran to much or to little tire psi…

15-18 all day everyday…those mickey’s will still be on the car this season.:eekdance:

[Previous page](https://forums.speedlife.net/t/f-body-pinion-seal-leak-what-to-do/55927.md?page=1)
