# FS: e30 EVERYTHING YOU COULD DESIRE
**URL:** https://forums.speedlife.net/t/fs-e30-everything-you-could-desire/30578
**Category:** Classifieds
**Created:** [June 8, 2007, 4:36pm UTC](https://forums.speedlife.net/t/fs-e30-everything-you-could-desire/30578 "2007-06-08T16:36:27Z")
**Posts on this page:** 15
**Page:** 1
### Author:  [@Coldaccord](https://forums.speedlife.net/u/Coldaccord)
#### Post date: [June 8, 2007, 4:36pm UTC](https://forums.speedlife.net/t/fs-e30-everything-you-could-desire/30578/1 "2007-06-08T16:36:27Z")
All prices are firm, in U.S. dollars, and do not include shipping. My paypal and e-mail are [Nerdigger@aol.com](mailto:Nerdigger@aol.com).
**SUSPENSION**
Eibach Ground Control Coilovers for non-M e30
375 in-lb springs for the front & 500 in-lb for the rear
This kit is set up for Bilstein Sports
Has about 7k on them. Kept incredibly clean, and come with everything they originally did
$345
Bilstein Sports
$250 **SOLD**
**COMPLETE EURO M20 W/99K!**
From my touring. 99k on it. EURO m20. no leaks, doesn’t burn any oil, no issues whatsoever. With clutch, flywheel, and Getrag 260 5 speed transmission, no grinds, no issues. Have pics (they’re just on my external hard drive which is at my parents house). Comes with alternator, p/s pump, starter, etc etc. everything it would normally come with (but no a/c compressor, my touring doesn’t have a/c)
$1300 w/tranny & everything
**MOTOR IS SOLD. TRANSMISISON STILL AVAILABLE**
**BALLER M20 PARTS**
Mahle 10.2:1 pistons. Brand new, in box. Come with all rings. Use “I” rods (I have a set w/60k on them in the “Used m20 parts” section below)
$550
Fresh cylinder head. Had ~65k on it. Got it cleaned, milled, 3 angle valve job, new valve seals, valves reseated
$525
Catcams 283/283 camshaft
**duration duration maximum lift lift at TDC**
[0.1mm+cl] [0.1mm+cl] [cl=0] [cl=0]
283/283 246/246 11.90/11.90mm 2.75/2.75mm
new in box
$275
Performance valve springs: full set
“the increased duration of a performance cam with an aggressive grind forces the valve to open and close at a much faster rate. This rapid opening and closing at high RPM can cause “valve float”. Valve float is the inability for a valve spring to close the valve fast enough to avoid piston contact.”
$250
m20 rocker arms. Full set. New in box.
$190
e30 rocker arm shafts (includes 2). New in box.
$70
m20 9mm spark plug wires. Barely used.
$80
Barely used SMT-6. Like new
$300
Dinan chip (I can’t remember if this is the real one or the knock-off, so I’ll price it at knock off price). For 173 ecu
$85
Euro 323i flywheel. ~11 lbs, so ~8 lbs lighter than stock m20b25. I had it resurfaced, but it’s got a little surface rust on there. Nothing serious, pictures make it look way more dirty than it is.
$95
**USED M20 PARTS**
351 DME. ~65k.
$50
Alternator. Spins freely.
$35
m20b25 (all these things have ~65k on them):
intake manifold
$40
Fuel pressure regulator
$15
Fuel rail
$15
injectors
$40
valve cover. I cleaned it up just a bit
$40
oil cooler & lines
$60
power steering pump pictured above.
$20
**SOLD**
o2 sensor
$45
ICV
$40
---
### Author:  [@Coldaccord](https://forums.speedlife.net/u/Coldaccord)
#### Post date: [June 8, 2007, 4:37pm UTC](https://forums.speedlife.net/t/fs-e30-everything-you-could-desire/30578/2 "2007-06-08T16:37:23Z")
m20b25 afm (x2)
$25
m20b25 throttle body and throttle position switch
$25
plug wire cover
$10
4.10 open diff. probably leaks.
$45
325ix dipstick
$10
wiring harness from ’88 325ix ~65k
$75
knee bolster. Perfect shape
$30
center console. Perfect shape.
$35
e-brake console. Perfect shape.
$20
throw back: Early model pass side taillight. Great shape (bought from Jordan). Bought it for my first e30 like 5 years ago and it just sat in my room.
$35
overhead panel, for sunroof cars. Had a bit of discoloration in the center where the rearview mirror goes, I sharpied it. Can’t even see it when installed
$20
late model 3rd brakelight
$10
**COMPLETE EURO M20 W/99K!**
From my touring. 99k on it. EURO m20. no leaks, doesn’t burn any oil, no issues whatsoever. With clutch, flywheel, and Getrag 260 5 speed transmission, no grinds, no issues. Have pics (they’re just on my external hard drive which is at my parents house). Comes with alternator, p/s pump, starter, etc etc. everything it would normally come with (but no a/c compressor, my touring doesn’t have a/c)
$1300 w/tranny & everything
**MOTOR IS SOLD. 5 SPEED TRANSMISSION STILL AVAILABLE**
**NEW M20 REPLACEMENT PARTS**
bottom end set part number 11-11-9-063-134 $25
head bolt set pn 11-12-1-726-478 $15
head gasket set pn 11-12-9-059-240 $45
main bearing set pn 11-21-1-706-847-6cyl $65
rod bearing set 11-24-1-284-849-6cyl $35
connecting rod bolt set 11-24-1-713-342 $50 **SOLD**
rear shock mount set 33-52-1-092-362 $25
transmission tail mount 22-31-1-094-916 (2) $10
guide bushing for driveshaft 26-11-1-207-096 $7
alternator belt 11-51-1-469-236 $3
power steering belt 32-42-1-469-239 $3
a/c compressor belt 64-52-1-466-043 $4
oil pan gasket (not cork, cork sucks) 11-13-1-730-234 $5
valve cover gasket 11-12-1-730-229 $7
clutch master cylinder 21-52-1-156-000 $55
clutch slave cylinder 21-52-1-116-300 $30
sachs clutch kit from bavauto;
“To replace your worn clutch you will have to remove the transmission from your BMW. This is not terribly difficult, but it is time consuming and you wouldn’t want to do it twice for the sake of incidental parts. This is why we have put together a clutch kit with all the items you should replace, not just the obvious ones. Our kit contains: an alignment tool, clutch disc, pressure plate, throw-out bearing, rear engine seal, pilot bearing, all transmission seals, exhaust gaskets, and a pivot pin. All our clutch components are manufactured by Sachs, Europe’s premier clutch manufacturer. Sachs clutch discs, pressure plates and throw out bearings are original equipment and are engineered to deliver maximum performance.”
Part number CK325I525
$230
engine mounts (2) 11-81-1-132-323 $25 for both
water pump 11-51-9-070-759 $55
coolant level sensor 61-31-1-378-320 $25
Bosch Super spark plugs (set) 12-12-9-061-869 $25
Timing belt kit 09-9320-000. comes with timing belt, tensioner, and replacement sticker $30
---
### Author:  [@Coldaccord](https://forums.speedlife.net/u/Coldaccord)
#### Post date: [June 8, 2007, 4:43pm UTC](https://forums.speedlife.net/t/fs-e30-everything-you-could-desire/30578/3 "2007-06-08T16:43:59Z")
forgot to mention
m20b25 rods 60k on them $50
m20b27 full block; crank, rods, pistons, pan, pump, all together. 155k. $95
---
### Author:  [@boardjnky4](https://forums.speedlife.net/u/boardjnky4)
#### Post date: [June 8, 2007, 5:42pm UTC](https://forums.speedlife.net/t/fs-e30-everything-you-could-desire/30578/4 "2007-06-08T17:42:52Z")
why not just put all those parts together and build a whole car lol?
---
### Author:  [@Coldaccord](https://forums.speedlife.net/u/Coldaccord)
#### Post date: [June 9, 2007, 7:52pm UTC](https://forums.speedlife.net/t/fs-e30-everything-you-could-desire/30578/5 "2007-06-09T19:52:16Z")
ground controls sold too.
you e30 guys are sleeping. you will never see this shit for this cheap. I just need to dump it all so I can buy the car’s new motor. shit will be tiiiiggghhhtt
mmm. 300hp ///m wagon. ///mmmmmmm
---
### Author:  [@Minglor](https://forums.speedlife.net/u/Minglor)
#### Post date: [June 10, 2007, 5:27pm UTC](https://forums.speedlife.net/t/fs-e30-everything-you-could-desire/30578/6 "2007-06-10T17:27:41Z")
Bump for a silly amount of E30 shit for sale.
Got any 4x100 wheels around?
---
### Author:  [@Coldaccord](https://forums.speedlife.net/u/Coldaccord)
#### Post date: [June 10, 2007, 7:36pm UTC](https://forums.speedlife.net/t/fs-e30-everything-you-could-desire/30578/7 "2007-06-10T19:36:50Z")
I’ve got a set of 14" bbs basketweaves with nice tires, but I might be picking up a 90 325i. if i don’t, they will be for sale. (I’m going 5 lug on the touring)
---
### Author:  [@cky89](https://forums.speedlife.net/u/cky89)
#### Post date: [June 10, 2007, 7:40pm UTC](https://forums.speedlife.net/t/fs-e30-everything-you-could-desire/30578/8 "2007-06-10T19:40:01Z")
you should have just built the whole damn car and sold it all together LOL
i wish i had a bimmer
GLWTS
---
### Author:  [@EvilJay](https://forums.speedlife.net/u/EvilJay)
#### Post date: [June 11, 2007, 6:56am UTC](https://forums.speedlife.net/t/fs-e30-everything-you-could-desire/30578/9 "2007-06-11T06:56:18Z")
If you do end up selling the basketweaves, fuck mingle, sell them to me. They would look better on an e30 than they would on a little girl miata.
---
### Author:  [@brent\_strong](https://forums.speedlife.net/u/brent_strong)
#### Post date: [June 11, 2007, 7:02am UTC](https://forums.speedlife.net/t/fs-e30-everything-you-could-desire/30578/10 "2007-06-11T07:02:38Z")
Trans for an M20?
---
### Author:  [@Minglor](https://forums.speedlife.net/u/Minglor)
#### Post date: [June 11, 2007, 1:32pm UTC](https://forums.speedlife.net/t/fs-e30-everything-you-could-desire/30578/11 "2007-06-11T13:32:51Z")
[quote=“EvilJay,post:9,topic:30578"”]
If you do end up selling the basketweaves, fuck mingle, sell them to me. They would look better on an e30 than they would on a little girl miata.
[/quote]
Suck a dick jay.
bump.
---
### Author:  [@Coldaccord](https://forums.speedlife.net/u/Coldaccord)
#### Post date: [June 12, 2007, 12:23am UTC](https://forums.speedlife.net/t/fs-e30-everything-you-could-desire/30578/12 "2007-06-12T00:23:35Z")
[quote=“brent\_strong,post:10,topic:30578"”]
Trans for an M20?
[/quote]
I’m not sure who the motor is going to right now. there are 3 dudes battling it out. 1 of which, who had first dibs but lives far (illinois, the other 2 are in toronto) doesn’t need the tranny, in which case I will sell it for $250, you can have the clutch too. no grinds or anything, great shape
---
### Author:  [@Coldaccord](https://forums.speedlife.net/u/Coldaccord)
#### Post date: [June 12, 2007, 12:24am UTC](https://forums.speedlife.net/t/fs-e30-everything-you-could-desire/30578/13 "2007-06-12T00:24:06Z")
[quote=“cky89,post:8,topic:30578"”]
you should have just built the whole damn car and sold it all together LOL
i wish i had a bimmer
GLWTS
[/quote]
obdI s52 \> stroked m20
plus, I could never sell my touring. can’t replace that shit
---
### Author:  [@newman](https://forums.speedlife.net/u/newman)
#### Post date: [June 12, 2007, 5:48am UTC](https://forums.speedlife.net/t/fs-e30-everything-you-could-desire/30578/14 "2007-06-12T05:48:53Z")
damnit. there’s not one e30 part i could possibly desire. I need diving board bumper trim, and crank windows…
got any?
---
### Author:  [@Coldaccord](https://forums.speedlife.net/u/Coldaccord)
#### Post date: [June 12, 2007, 10:43am UTC](https://forums.speedlife.net/t/fs-e30-everything-you-could-desire/30578/15 "2007-06-12T10:43:39Z")
nah man, sorry. bounce on those ugly db’s and get some euro’s! i sent you a link for a set a while back