# Percy xx carbon exhaust gasket material - amazing stuff **URL:** \ **Category:** NYSpeed Automotive\ **Created:** [January 19, 2007, 12:34am UTC](https://forums.speedlife.net/t/percy-xx-carbon-exhaust-gasket-material-amazing-stuff/23286 "2007-01-19T00:34:09Z")\ **Posts on this page:** 11\ **Page:** 1
**Author:** ![HotRodKid](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/hotrodkid/32/7609_2.png) [@HotRodKid](https://forums.speedlife.net/u/HotRodKid)\ **Post date:** [January 19, 2007, 12:34am UTC](https://forums.speedlife.net/t/percy-xx-carbon-exhaust-gasket-material-amazing-stuff/23286/1 "2007-01-19T00:34:09Z")
well Somedudes car keeps destroying exhaust gaskets @ the flex pipe, it ate up the Mr Gasket stuff, it burnted a hole in some aluminium plate … this car is like letting cookie monster loose loose in a bakery so a while ago i made a thread on [HR.com](http://HR.com) asking what the heck we should use, one of the replys i received was “percys xx carbon gasket material” as luck would have it, about the same time i got the recomendation, Alex was out of town visiting friends, one of which had said “lets see what summit racing has for you” summit also suggested the percy xx, and alex purchased some and had it shipped to his house here when we got it, i made a gasket for the offending spot, and we installed it i took a scrap of the Percy’s xx, and held it in front of the 150,000 btu torpedo heater, if i remember correctly, steel gets red hot around 3000 degrees F … so how hot would the exhaust be 1" from the end of the heater ? 15 seconds, the shine on the material faded slightly 30 seconds, slightly more fade 45 seconds - fading has stopped 1 minute, a very slight wiff of smoke when the material is pulled from the heat 1 minute 30 seconds - smoke has stopped, no visable change 2 minutes, my knuckles are screaming hot, i press on 5 minutes of holding this stuff a mere inch off the red hot plate at the end of the torpedo heater, right in the flow of hot exhaust… and the heated section is barely different then the unheated section here is a quote from the Percy site: > These gaskets can withstand long term direct exposure to over 2000° farenhight. I FIND THIS STATEMENT TO BE AMAZINGLY ACCURATE! also, after installing the gasket, i decided to run some mig welds across the flanges, ensuring that the 2 bolt flange we’re using wouldnt rock open and cause a leak. the gasket material poking out at either end of the weld failed to burst into flames it failed to smoke it failed to discolor for the record, i repeated the test again w/ the mister gasket material, it once again started to char after a meer 5-10 seconds in the heat, letting off a massive amount of smoke in the process 30 seconds would have reduced the Mr Gasket material to its steel core heres the listing for percy gaskets on summit racing [http://store.summitracing.com/egnse](http://store.summitracing.com/egnse)…+115+4294925237 heres the percy website for said gaskets [http://www.percyshp.com/index.php?o...&id=4&Itemid=31](http://www.percyshp.com/index.php?o...&id=4&Itemid=31) heres the main page for the percy website, in case you want to see what else they offer [http://www.percyshp.com](http://www.percyshp.com) ---
**Author:** ![Phoenix\_305](https://avatars.discourse-cdn.com/v4/letter/p/977dab/32.png) [@Phoenix\_305](https://forums.speedlife.net/u/Phoenix_305)\ **Post date:** [January 19, 2007, 12:36am UTC](https://forums.speedlife.net/t/percy-xx-carbon-exhaust-gasket-material-amazing-stuff/23286/2 "2007-01-19T00:36:39Z")
Glad it might not leak finally. Sounds like fun stuff. :tup: ---
**Author:** ![LAFENGAS](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/lafengas/32/7573_2.png) [@LAFENGAS](https://forums.speedlife.net/u/LAFENGAS)\ **Post date:** [January 19, 2007, 5:41am UTC](https://forums.speedlife.net/t/percy-xx-carbon-exhaust-gasket-material-amazing-stuff/23286/3 "2007-01-19T05:41:13Z")
you can go to McMaster-Carr, pick up “Ceramic Fiber Sheet Gaskets” and cut them yourselft. Good up to 2600°F. FYI. ---
**Author:** ![97FormulaWS-6](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/97formulaws-6/32/7384_2.png) [@97FormulaWS-6](https://forums.speedlife.net/u/97FormulaWS-6)\ **Post date:** [January 19, 2007, 6:05am UTC](https://forums.speedlife.net/t/percy-xx-carbon-exhaust-gasket-material-amazing-stuff/23286/4 "2007-01-19T06:05:12Z")
Yea, that stuff is great… Percy’s just re-labels it, it’s actually made by another company… earls uses it in their header and collector gaskets… ahhhhhh… it’s a Parker-Hannifin product. Wonderful stuff. ---
**Author:** ![cruciform](https://avatars.discourse-cdn.com/v4/letter/c/9d8465/32.png) [@cruciform](https://forums.speedlife.net/u/cruciform)\ **Post date:** [January 19, 2007, 7:32am UTC](https://forums.speedlife.net/t/percy-xx-carbon-exhaust-gasket-material-amazing-stuff/23286/5 "2007-01-19T07:32:14Z")
I kept thinking I was getting complements, as my name is Percy… 🙂 ---
**Author:** ![HotRodKid](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/hotrodkid/32/7609_2.png) [@HotRodKid](https://forums.speedlife.net/u/HotRodKid)\ **Post date:** [January 19, 2007, 2:23pm UTC](https://forums.speedlife.net/t/percy-xx-carbon-exhaust-gasket-material-amazing-stuff/23286/6 "2007-01-19T14:23:53Z")
and my email to them is now on the front page of their site: [http://www.percyshp.com/](http://www.percyshp.com/) ---
**Author:** ![Bacon](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/bacon/32/7230_2.png) [@Bacon](https://forums.speedlife.net/u/Bacon)\ **Post date:** [January 19, 2007, 3:44pm UTC](https://forums.speedlife.net/t/percy-xx-carbon-exhaust-gasket-material-amazing-stuff/23286/7 "2007-01-19T15:44:46Z")
Definitely a more fun now, the car is getting nuckin futty. ---
**Author:** ![somedude](https://avatars.discourse-cdn.com/v4/letter/s/ecd19e/32.png) [@somedude](https://forums.speedlife.net/u/somedude)\ **Post date:** [January 19, 2007, 7:35pm UTC](https://forums.speedlife.net/t/percy-xx-carbon-exhaust-gasket-material-amazing-stuff/23286/8 "2007-01-19T19:35:08Z")
lol yeah the car moves a better now. damn nick you should have linked them to pics of the car. but who would have thought that it would make the front page. thats pretty cool. not even a mention of a turbo taurus in that article… you call your self a fabricator. ---
**Author:** ![HotRodKid](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/hotrodkid/32/7609_2.png) [@HotRodKid](https://forums.speedlife.net/u/HotRodKid)\ **Post date:** [January 19, 2007, 7:39pm UTC](https://forums.speedlife.net/t/percy-xx-carbon-exhaust-gasket-material-amazing-stuff/23286/9 "2007-01-19T19:39:41Z")
the car is mentioned in the thread on [hotrodders.com](http://hotrodders.com), they chose not to include it i guess ---
**Author:** ![buffalove](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/buffalove/32/7460_2.png) [@buffalove](https://forums.speedlife.net/u/buffalove)\ **Post date:** [January 19, 2007, 9:25pm UTC](https://forums.speedlife.net/t/percy-xx-carbon-exhaust-gasket-material-amazing-stuff/23286/10 "2007-01-19T21:25:00Z")
> ``` > These gaskets can withstand long term direct exposure to over 2000° farenhight. > > ``` Some kind of new swedish measuring unit? Lol But yeah, that stuff seems to be holding up. ---
**Author:** ![HotRodKid](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/hotrodkid/32/7609_2.png) [@HotRodKid](https://forums.speedlife.net/u/HotRodKid)\ **Post date:** [January 19, 2007, 10:18pm UTC](https://forums.speedlife.net/t/percy-xx-carbon-exhaust-gasket-material-amazing-stuff/23286/11 "2007-01-19T22:18:35Z")
^^^ haha, beat you to it. in my original email i told them to fix the spelling of it