# S14 Ichiba Extended Studs

**URL:** <https://forums.speedlife.net/t/s14-ichiba-extended-studs/210560>\
**Category:** Classifieds\
**Created:** [March 27, 2011, 4:32pm UTC](https://forums.speedlife.net/t/s14-ichiba-extended-studs/210560 "2011-03-27T16:32:31Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![Sandersb4671](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/sandersb4671/32/5693_2.png) [@Sandersb4671](https://forums.speedlife.net/u/Sandersb4671)\
**Post date:** [March 27, 2011, 4:32pm UTC](https://forums.speedlife.net/t/s14-ichiba-extended-studs/210560/1 "2011-03-27T16:32:31Z")

</div>

As title states, I’m selling a set of 10 BNIB S14 knurl size Ichiba hardened extended studs. I bought these under the impression that J30 front hubs were the same stud size knurl as an S14, but they’re not. I never installed these, or even tried to. They were measured before any test fitting, so they are still brand new condition.  
$30.  
Picture is not mine but these look exactly the same.  
 ![http://img526.imageshack.us/img526/4222/41238758.jpg](http://img526.imageshack.us/img526/4222/41238758.jpg)[/IMG]

---

<div class="post-metadata">

**Author:** ![crunkride](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/crunkride/32/5783_2.png) [@crunkride](https://forums.speedlife.net/u/crunkride)\
**Post date:** [March 27, 2011, 4:45pm UTC](https://forums.speedlife.net/t/s14-ichiba-extended-studs/210560/2 "2011-03-27T16:45:44Z")

</div>

I had NISMO front studs put on the rear of my S14 (front knurls are greater overall diameter than rear, fyi)., by drilling out the holes a little bigger. You just need patience, a sharp bit/drill press, and some cutting fluid…Might help you out.

---

<div class="post-metadata">

**Author:** ![Sandersb4671](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/sandersb4671/32/5693_2.png) [@Sandersb4671](https://forums.speedlife.net/u/Sandersb4671)\
**Post date:** [March 27, 2011, 4:52pm UTC](https://forums.speedlife.net/t/s14-ichiba-extended-studs/210560/3 "2011-03-27T16:52:52Z")

</div>

Yeah, the only problem I found with that (I did it with my 4 bolt hubs) was that without the ability to cut new knurls in the drilled out hubs, the studs can wear out and become loose. Then again, I was using shitty circuit sports aluminum studs…

---

<div class="post-metadata">

**Author:** ![rmallari](https://avatars.discourse-cdn.com/v4/letter/r/898d66/32.png) [@rmallari](https://forums.speedlife.net/u/rmallari)\
**Post date:** [March 27, 2011, 5:08pm UTC](https://forums.speedlife.net/t/s14-ichiba-extended-studs/210560/4 "2011-03-27T17:08:22Z")

</div>

billy, i want these…tonight, asap.  
whats the length by the way