# Some of our projects!!
**URL:** https://forums.speedlife.net/t/some-of-our-projects/260685
**Category:** Vendor Marketplace
**Created:** [October 1, 2011, 3:34pm UTC](https://forums.speedlife.net/t/some-of-our-projects/260685 "2011-10-01T15:34:39Z")
**Posts on this page:** 20
**Page:** 4
### Author:  [@KrazyKid](https://forums.speedlife.net/u/KrazyKid)
#### Post date: [October 24, 2011, 8:17am UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/61 "2011-10-24T08:17:21Z")
Glad to see you are a realist! The stuff isnt cheap, and there is a lot behind the install than meets the eyes that makes the labor & hours spent add up quickly. Lots of people see a car dumped out on air and think ‘bags and switches’… there is soooo much more to it than that!!!
To answer your questions. The audi is my brothers daily. It doesn’t leak, so it could be a set it and forget it thing. The ride is BETTER than stock even being 3 inches lower at ride height. If you wanted to drive it right now across the country (NOT CANADA DAVE lol) to Cali and back, I would leave tonight.
Winter. You see big rigs and dump trucks running in the winter right! We are going to rock the audi all winter too. We got a good water trap PRE valve manifold. and they make anti freeze oilers for the system too we are going to try. Its the same thing the big rigs rock. It also helps that the valves, compressor and tank is in the trunk, so it sucks in cabin air, so maybe that will be less humid?
Keep the water out of the valves, and they wont freeze, keep the water out of the lines, fittings and bags and they wont freeze. good to go. At least that’s the plan. Time will tell.
---
### Author:  [@jdaniels](https://forums.speedlife.net/u/jdaniels)
#### Post date: [October 24, 2011, 8:36am UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/62 "2011-10-24T08:36:12Z")
> [@Thursday night all nighter to 9-5 on Friday..in bar attire, naturally](https://forums.speedlife.net/t/thursday-night-all-nighter-to-9-5-on-friday-in-bar-attire-naturally/43842/50):
>
> (NOT CANADA DAVE lol)
[ame][http://www.youtube.com/watch?v=sekLEG8xsOs[/ame]](http://www.youtube.com/watch?v=sekLEG8xsOs%5B/ame%5D)
---
### Author:  [@ninety1two40](https://forums.speedlife.net/u/ninety1two40)
#### Post date: [October 24, 2011, 9:07am UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/63 "2011-10-24T09:07:58Z")
:rofl
---
### Author:  [@KrazyKid](https://forums.speedlife.net/u/KrazyKid)
#### Post date: [November 12, 2011, 8:57am UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/64 "2011-11-12T08:57:03Z")
Mike has been learning how to run a lathe and cant wait for a mill here at the shop!
6061 aluminum shift knob for the T5 trans going into the MGB swap project.
---
### Author:  [@KrazyKid](https://forums.speedlife.net/u/KrazyKid)
#### Post date: [November 22, 2011, 8:33am UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/65 "2011-11-22T08:33:53Z")
In effort to organize tools and get more efficient, we built a badass welding cart.
It has a Miller 180 MIG, BIG argon tank, Thermal Dynamics 38 plasma cutter set up for fine cut, tool box for consumables, grinders, hand tools, markers, tape measures, squares, clamps, gloves and safety goggles, etc all in once place. Nice stainless steel work bench on top, big casters to roll it around and plumbed for air and 220. So you wheel it to your work area, plug the cart into the shop air supply and a 220V drop, and get to work. no tripping over air hoses and cords!
Its even got a cup holder!!!
I also built the coolest Vinyl cutter stand ever! Yes that’s a 18" Z06 wheel!
Made a turbo inlet for a VR4, stock turbo to SLP 4" maf. Spun a bung for the diverter valve too.
---
### Author:  [@McBitchin](https://forums.speedlife.net/u/McBitchin)
#### Post date: [November 22, 2011, 8:51am UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/66 "2011-11-22T08:51:34Z")
Its a 16g but close enough to stock :lol
---
### Author:  [@NickAlero](https://forums.speedlife.net/u/NickAlero)
#### Post date: [November 22, 2011, 8:41pm UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/67 "2011-11-22T20:41:22Z")
Good to see it getting some love! KK you may have another project coming up soon…
---
### Author:  [@big\_red](https://forums.speedlife.net/u/big_red)
#### Post date: [November 23, 2011, 5:40am UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/68 "2011-11-23T05:40:20Z")
solid work mike
---
### Author:  [@KrazyKid](https://forums.speedlife.net/u/KrazyKid)
#### Post date: [November 23, 2011, 5:41am UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/69 "2011-11-23T05:41:13Z")
Thanks gents!
---
### Author:  [@big\_red](https://forums.speedlife.net/u/big_red)
#### Post date: [November 23, 2011, 5:43am UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/70 "2011-11-23T05:43:48Z")
ill make those templates for my can and you can post them shits up too.
---
### Author:  [@KrazyKid](https://forums.speedlife.net/u/KrazyKid)
#### Post date: [November 23, 2011, 6:20am UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/71 "2011-11-23T06:20:09Z")
> [@big red"](#):
>
> ill make those templates for my can and you can post them shits up too.
Werd. decide on polished or a color for PC?
---
### Author:  [@underboosted](https://forums.speedlife.net/u/underboosted)
#### Post date: [November 23, 2011, 11:14am UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/72 "2011-11-23T11:14:54Z")
Your cutter didn’t come with a stand? Mine came with one that has rollers for the roll to sit on.
---
### Author:  [@h0twh3els](https://forums.speedlife.net/u/h0twh3els)
#### Post date: [November 23, 2011, 11:16am UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/73 "2011-11-23T11:16:38Z")
> [@S13 Coupe Build | Last Update: 20-May](https://forums.speedlife.net/t/s13-coupe-build-last-update-20-may/43006/88):
>
> Your cutter didn’t come with a stand? Mine came with one that has rollers for the roll to sit on.
It did not… However, even if it did… We would have still made one CRC style :tbu
---
### Author:  [@KrazyKid](https://forums.speedlife.net/u/KrazyKid)
#### Post date: [November 23, 2011, 12:02pm UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/74 "2011-11-23T12:02:43Z")
> [@S13 Coupe Build | Last Update: 20-May](https://forums.speedlife.net/t/s13-coupe-build-last-update-20-may/43006/88):
>
> Your cutter didn’t come with a stand? Mine came with one that has rollers for the roll to sit on.
Stand was a 50$ option.
Z06 wheel i had was cracked so it was just a conversation piece to begin with, so I took it to another level.
Rollers are not necessary, the roll just spins around as it needs to like you see it… I am not a running a sticker biz so it doesn’t need to be perfect, it just needs to work.
---
### Author:  [@big\_red](https://forums.speedlife.net/u/big_red)
#### Post date: [November 23, 2011, 3:24pm UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/75 "2011-11-23T15:24:14Z")
> [@5/10/08 - NYSpeed Photoshoot EVERYTHING IS SET AND READY TO GO FOR SATURDAY](https://forums.speedlife.net/t/5-10-08-nyspeed-photoshoot-everything-is-set-and-ready-to-go-for-saturday/46358/57):
>
> Werd. decide on polished or a color for PC?
Prob gonna paint it to match the bay, dark charcoal
---
### Author:  [@TurboTravis](https://forums.speedlife.net/u/TurboTravis)
#### Post date: [November 24, 2011, 12:49pm UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/76 "2011-11-24T12:49:46Z")
Mike, Evo needs an IC pipe in the Spring (one of them has 1 extra coupling that has leaked a few times on me), I’ll get with you a few weeks beforehand, I think you’ll be able to do it easily in a few hours while I wait. I’ll trailer it down.
---
### Author:  [@PJB](https://forums.speedlife.net/u/PJB)
#### Post date: [November 24, 2011, 12:51pm UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/77 "2011-11-24T12:51:55Z")
I might consider having you make a skidplate on my quad. The plastic one is cracked and plastic sucks for that anyway.
I dont give a fuck if you make it out of a street sign.
---
### Author:  [@h0twh3els](https://forums.speedlife.net/u/h0twh3els)
#### Post date: [November 24, 2011, 3:36pm UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/78 "2011-11-24T15:36:06Z")
Travis, I look forward to seeing the Evo again!
PJB… Bring the quad by, I’m sure we can make something for it!
---
### Author:  [@DeathbyRT](https://forums.speedlife.net/u/DeathbyRT)
#### Post date: [November 24, 2011, 3:43pm UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/79 "2011-11-24T15:43:51Z")
100% in for a roll bar. Have already gone through in depth with woody about what i want. Just need to get up there so he can take a look at it. Looking forward to it. Need some mid pipes, motor mounts and other stuff as well.
---
### Author:  [@PJB](https://forums.speedlife.net/u/PJB)
#### Post date: [November 24, 2011, 5:32pm UTC](https://forums.speedlife.net/t/some-of-our-projects/260685/80 "2011-11-24T17:32:12Z")
> [@Kenne Bell Cobra anyone?!](https://forums.speedlife.net/t/kenne-bell-cobra-anyone/46700/48):
>
> Travis, I look forward to seeing the Evo again!
>
> PJB… Bring the quad by, I’m sure we can make something for it!
Ive gotta get it running first, probably going to take it somewhere this weekend for repair but I could bring it or just the skid plate up when its fixed. The current one is a good design I suppose but its just the wrong material.
[Previous page](https://forums.speedlife.net/t/some-of-our-projects/260685.md?page=3)
[Next page](https://forums.speedlife.net/t/some-of-our-projects/260685.md?page=5)