# Tint Removal **URL:** \ **Category:** NYSpeed Automotive\ **Created:** [January 2, 2007, 7:36pm UTC](https://forums.speedlife.net/t/tint-removal/22456 "2007-01-02T19:36:42Z")\ **Posts on this page:** 17\ **Page:** 2
**Author:** ![ly555is](https://avatars.discourse-cdn.com/v4/letter/l/3bc359/32.png) [@ly555is](https://forums.speedlife.net/u/ly555is)\ **Post date:** [January 18, 2007, 3:00pm UTC](https://forums.speedlife.net/t/tint-removal/22456/21 "2007-01-18T15:00:23Z")
1. get phone book 2. call tint places for estimate /thread don’t do it yourself. it’s a fucking bitch, just pay someone else to do it pro stylez. ---
**Author:** ![ultradriver10000](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/ultradriver10000/32/7397_2.png) [@ultradriver10000](https://forums.speedlife.net/u/ultradriver10000)\ **Post date:** [January 19, 2007, 3:51pm UTC](https://forums.speedlife.net/t/tint-removal/22456/22 "2007-01-19T15:51:49Z")
goo gone is god ---
**Author:** ![Violator](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/violator/32/7278_2.png) [@Violator](https://forums.speedlife.net/u/Violator)\ **Post date:** [January 19, 2007, 5:02pm UTC](https://forums.speedlife.net/t/tint-removal/22456/23 "2007-01-19T17:02:39Z")
> [@ultradriver10000](#): > > goo gone is god Bingo. Only good advice I have seen so far. Dont scrape anything. Peel the tints off. Do it solwly so the plastic stays together and comes off in large sections. Once the plastic is off and the glue remains: Get a bottle of GOO-GONE spray (Tops). Put a towel or sheet of painters plastic over the interiordoor panel… tuck the edge under the rubber strip between panel and window. SOAK the entire glass pane. Take a garbage bag or another sheet of plastic and slap it on the wet pane. Leave it there for a hour. Get a razor blade(single edge is better) and slowly get the glue off. Wipe the blade on a paper towel after each pass. The glue will come off very easily. If there is a stubborn spot, spray it again. Wait 5 min, continue. This is not hard to do. Use a credit card for the rear window. ---
**Author:** ![IntegLS94](https://avatars.discourse-cdn.com/v4/letter/i/ecd19e/32.png) [@IntegLS94](https://forums.speedlife.net/u/IntegLS94)\ **Post date:** [January 19, 2007, 8:32pm UTC](https://forums.speedlife.net/t/tint-removal/22456/24 "2007-01-19T20:32:23Z")
> [@Violator](#): > > Bingo. Only good advice I have seen so far. > > Dont scrape anything. Peel the tints off. Do it solwly so the plastic stays together and comes off in large sections. Once the plastic is off and the glue remains: Get a bottle of GOO-GONE spray (Tops). Put a towel or sheet of painters plastic over the interiordoor panel… tuck the edge under the rubber strip between panel and window. SOAK the entire glass pane. Take a garbage bag or another sheet of plastic and slap it on the wet pane. Leave it there for a hour. Get a razor blade(single edge is better) and slowly get the glue off. Wipe the blade on a paper towel after each pass. The glue will come off very easily. If there is a stubborn spot, spray it again. Wait 5 min, continue. > > This is not hard to do. Use a credit card for the rear window. just to clear things up, you obviously remove the plastic bag off the window before rubbing the glue off? ---
**Author:** ![Violator](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/violator/32/7278_2.png) [@Violator](https://forums.speedlife.net/u/Violator)\ **Post date:** [January 19, 2007, 8:39pm UTC](https://forums.speedlife.net/t/tint-removal/22456/25 "2007-01-19T20:39:37Z")
> [@IntegLS94](#): > > just to clear things up, you obviously remove the plastic bag off the window before rubbing the glue off? Yes. The bag is just there to keep the stuff from drying and running. You can almost skip the bag if you want since Goo Gone does not dry for a looong time. I like using it since it reduces runs as well. ---
**Author:** ![Nikuk](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/nikuk/32/7254_2.png) [@Nikuk](https://forums.speedlife.net/u/Nikuk)\ **Post date:** [January 19, 2007, 9:06pm UTC](https://forums.speedlife.net/t/tint-removal/22456/26 "2007-01-19T21:06:40Z")
holy shit… this topic comes up once per month. at least. get started at a corner, peel a tab use a heat gun - or hair dryer once the plastic is warm slowly peel the plastic (tint) away from the window. continue to “walk” the heat just infront of where You are pulling. You can peel a Coupe’s side window in \>2 minutes. This also removes the majority of the glue. Get a can of NON chlorinate brake cleaner. spray 1/4 to 1/3 of the glass, wipe the glue off with a paper towel. Any tough spots, use a one edged razor blade with the brake clean. I’ve done this on 6-8 cars now. This summer it took me 20 minutes TOTAL (and 1 can of kleen) to de-tint an 87 Mustang (hatchback, 1/4s, and sides). Jesus I need to just get a camera, make a DIY, and have someone sticky it. ---
**Author:** ![IntegLS94](https://avatars.discourse-cdn.com/v4/letter/i/ecd19e/32.png) [@IntegLS94](https://forums.speedlife.net/u/IntegLS94)\ **Post date:** [January 19, 2007, 9:52pm UTC](https://forums.speedlife.net/t/tint-removal/22456/27 "2007-01-19T21:52:45Z")
> [@Violator](#): > > Yes. The bag is just there to keep the stuff from drying and running. > > You can almost skip the bag if you want since Goo Gone does not dry for a looong time. I like using it since it reduces runs as well. i figured as much…i’m going to give your methods a shot. Would it be in my best interest to wait until summer when the car is hot? or with the goo gone does it matter the temp of the tint and glass? thanks for the input ---
**Author:** ![Violator](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/violator/32/7278_2.png) [@Violator](https://forums.speedlife.net/u/Violator)\ **Post date:** [January 20, 2007, 12:23am UTC](https://forums.speedlife.net/t/tint-removal/22456/28 "2007-01-20T00:23:34Z")
> [@IntegLS94](#): > > i figured as much…i’m going to give your methods a shot. Would it be in my best interest to wait until summer when the car is hot? or with the goo gone does it matter the temp of the tint and glass? > > thanks for the input Goo Gone is probably mostly petroleum based so I doubt it will freeze but I would recommend you do this in a garage or where the temp is above freezing. The warmer it is the faster materials melt, soak, ect. It would just make your life easier. Try to find a heated garage for 2 hours and you are golden. ---
**Author:** ![98GCL](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/98gcl/32/7366_2.png) [@98GCL](https://forums.speedlife.net/u/98GCL)\ **Post date:** [January 20, 2007, 6:19am UTC](https://forums.speedlife.net/t/tint-removal/22456/29 "2007-01-20T06:19:59Z")
Throw bricks through the tinted windows, the insurance company will replace it for free and your rear defroster will be brand new. :gotme: ---
**Author:** ![IntegLS94](https://avatars.discourse-cdn.com/v4/letter/i/ecd19e/32.png) [@IntegLS94](https://forums.speedlife.net/u/IntegLS94)\ **Post date:** [January 20, 2007, 8:07am UTC](https://forums.speedlife.net/t/tint-removal/22456/30 "2007-01-20T08:07:11Z")
> [@98GCL](#): > > Throw bricks through the tinted windows, the insurance company will replace it for free and your rear defroster will be brand new. :gotme: yea she has no glass coverage…trust me i thought about it ---
**Author:** ![slasky](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/slasky/32/7408_2.png) [@slasky](https://forums.speedlife.net/u/slasky)\ **Post date:** [January 20, 2007, 8:50am UTC](https://forums.speedlife.net/t/tint-removal/22456/31 "2007-01-20T08:50:26Z")
> [@Nikuk](#): > > holy shit… this topic comes up once per month. at least. > > get started at a corner, peel a tab > use a heat gun - or hair dryer > once the plastic is warm slowly peel the plastic (tint) away from the window. continue to “walk” the heat just infront of where You are pulling. > You can peel a Coupe’s side window in \>2 minutes. > > This also removes the majority of the glue. > > Get a can of NON chlorinate brake cleaner. spray 1/4 to 1/3 of the glass, wipe the glue off with a paper towel. > Any tough spots, use a one edged razor blade with the brake clean. > > I’ve done this on 6-8 cars now. This summer it took me 20 minutes TOTAL (and 1 can of kleen) to de-tint an 87 Mustang (hatchback, 1/4s, and sides). > > Jesus I need to just get a camera, make a DIY, and have someone sticky it. Does this work for back windows with defrosters too? ---
**Author:** ![Nikuk](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/nikuk/32/7254_2.png) [@Nikuk](https://forums.speedlife.net/u/Nikuk)\ **Post date:** [January 20, 2007, 8:56am UTC](https://forums.speedlife.net/t/tint-removal/22456/32 "2007-01-20T08:56:50Z")
> [@slasky](#): > > Does this work for back windows with defrosters too? Yes. I’ve done it a few times. Because You are NOT SCRAPING anything it doesnt cause a problem. **IF** there is any residue left in the defrost grid, be liberal with the brake kleen. OBviously put down something to cover carpet / seats for overspray. The GLUE RESIDUE WILL LITERALLY WIPE RIGHT OFF. ---
**Author:** ![Nikuk](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/nikuk/32/7254_2.png) [@Nikuk](https://forums.speedlife.net/u/Nikuk)\ **Post date:** [January 20, 2007, 8:57am UTC](https://forums.speedlife.net/t/tint-removal/22456/33 "2007-01-20T08:57:59Z")
Matter of fact, I’ll be happy to show You. Feel free to swing by… Ill break out the heat gun and You bring a can of brake clean. edit - sorry, I just realized that You were in roch. ---
**Author:** ![Violator](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/violator/32/7278_2.png) [@Violator](https://forums.speedlife.net/u/Violator)\ **Post date:** [January 20, 2007, 11:12am UTC](https://forums.speedlife.net/t/tint-removal/22456/34 "2007-01-20T11:12:44Z")
Good heat gun tech. Just understand that if you get Brake Kleen on any plastic or rubber, it will stain or turn to shit. Make sure everything is covered well. ---
**Author:** ![RedConquestTSi](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/redconquesttsi/32/7326_2.png) [@RedConquestTSi](https://forums.speedlife.net/u/RedConquestTSi)\ **Post date:** [January 20, 2007, 2:51pm UTC](https://forums.speedlife.net/t/tint-removal/22456/35 "2007-01-20T14:51:53Z")
Having worked in detailing for over 3 years, at 2 different detail shops…we use steel wool and windex to remove glue left behind from stickers on heating elements. It doesnt hurt anything. ---
**Author:** ![91MR2](https://yyz2.discourse-cdn.com/flex034/user_avatar/forums.speedlife.net/91mr2/32/7217_2.png) [@91MR2](https://forums.speedlife.net/u/91MR2)\ **Post date:** [January 20, 2007, 7:00pm UTC](https://forums.speedlife.net/t/tint-removal/22456/36 "2007-01-20T19:00:12Z")
Both my Lotus and MR2 had tint when I got them. I immediatly removed them from both cars. Just takes a little time with windex and a few razors. As long as you don’t allow the blades to dull, it’s about as easy as it gets. ---
**Author:** ![TurboTSi](https://avatars.discourse-cdn.com/v4/letter/t/22d042/32.png) [@TurboTSi](https://forums.speedlife.net/u/TurboTSi)\ **Post date:** [January 21, 2007, 8:16am UTC](https://forums.speedlife.net/t/tint-removal/22456/37 "2007-01-21T08:16:16Z")
> [@Nikuk](#): > > Matter of fact, I’ll be happy to show You. Feel free to swing by… Ill break out the heat gun and You bring a can of brake clean. I’ll take you up on the Nick when it gets a bit nicer… all 5 windows need it, you can document it and post it as a DIY. I’ll bring the beer! [Previous page](https://forums.speedlife.net/t/tint-removal/22456.md?page=1)