FS: DSM stuff from my barn and some 18's.

All of this is pretty much best offer, I decided to go through my barn and found all sorts of stuff I haven’t seen in a year or two.

$40 - ARP mainstuds. Used, but in good condition.

B/O - 4g64 7 bolt block. Main cap has been honed IIRC, block was definitely honed, decked, and hot tanked. Is a bit dirty as its been sitting for awhile but this block is literally clean and assembly ready. You’d just have to order some components and you’re good to go.

B/O - Timing belt top cover. Apparently I forgot to sell it with the car?

B/O - Rear strut tower covers. Gray in color.

B/O - 2g TB. Good condition, has whatever sensors are/were on the car.

B/O - 2g coolant housing. Has coolant temperature sensor.

$500 - 18" Enkei RSF-2s, with some realllllly bad Fuzion tires. 3 need to be replaced, one is like new. All wheels are in MINT condition except for one wheel which has some scuffs/scrapes to the inner diameter from when my brake caliper sheared the bolts off and went for a ride.

As I sort through this, I’ll post if I have more. Pics avail upon request, but a lot of this stuff is pretty self explanatory so I’ll only post if you really want them.

Shawn

in for pics of wheels.

Got an email address you wanna PM me? If not, I’ll have some up on photobucket in a bit.

Shawn

Hey Shawn! Long time no see!!!

Hey man, how ya been? Don’t see none of you folks anymore since I done be out of the DSM scene.

Shawn

post lug pattern, offset, and width for those wheels

They’re dual bolt pattern. 5x100 and 5x114.3 or whatever the weird number was (5x4.5 IIRC). Wheel size is 18x7.

Backspacing is 40mm IIRC. It’s been awhile now. I can measure if it’s crucial for anyone.

Wheels are guaranteed to fit DSM’s, and come with center caps also.



Wheels are dirty, but flawless on the outside. Only damage to any of them is shown in the second photo and barely noticeable past rotor, caliper, etc…

Ok, I found more stuff. We have:

Valve cover. Good shape, no cracks. One spark plug cover hole has a chip out the side but hardware still threads in. - B/O
http://i260.photobucket.com/albums/ii12/xtoyz/car%20crap/101_0252-1.jpg
http://i260.photobucket.com/albums/ii12/xtoyz/car%20crap/101_0253-1.jpg

Bare 1g head with matching cam caps. Good shape, but BARE. - B/O
http://i260.photobucket.com/albums/ii12/xtoyz/car%20crap/101_0254.jpg
http://i260.photobucket.com/albums/ii12/xtoyz/car%20crap/101_0255-1.jpg
http://i260.photobucket.com/albums/ii12/xtoyz/car%20crap/101_0256.jpg

2g o2 housing. Decent shape, no cracks - B/O
http://i260.photobucket.com/albums/ii12/xtoyz/car%20crap/101_0249.jpg

2g front case + oil pump - B/O
http://i260.photobucket.com/albums/ii12/xtoyz/car%20crap/101_0245.jpg
http://i260.photobucket.com/albums/ii12/xtoyz/car%20crap/101_0246.jpg

2g oil filter housing - B/O
http://i260.photobucket.com/albums/ii12/xtoyz/car%20crap/101_0247.jpg

Blown T25 with a great exhaust housing. Would be great for swapping onto another turbo or as a core for a t28? - B/O
http://i260.photobucket.com/albums/ii12/xtoyz/car%20crap/101_0243.jpg
http://i260.photobucket.com/albums/ii12/xtoyz/car%20crap/101_0244.jpg

7 bolt flywheel. Was recently machined and then the car had a 6bolt swapped in. Could use a quick polishing (it’s been sitting awhile). - B/O.
http://i260.photobucket.com/albums/ii12/xtoyz/car%20crap/101_0248.jpg

I’ll be editing these two posts in the next few minutes to show the photos for each of these things too.

these would allow you to run some nice brakes…

18’s seem kinda big for a dsm. im in the market for some wheels and thats a good price but im not baaaaaaaaallllliiiin enough to have 18’s

glws

I miss my DSM :frowning:

GLWS!