I have a New SMT-6 For sale, comes with all the cables/software harnass
looking for ~250
he SMT6 is universal piggy back system, designed to allow you to tune almost ANY electronically fuel injected engine. Signals are modified on maps found within the SMT6 unit itself, and the Windows Tuning Software. Installation and tuning is simple and once installed the engine can be re-tuned by anyone with a laptop or PC, comms cable and the Tuning Software.
An average installation consists of connecting 6 wires to the vehicle’s original wiring loom, changing the settings of the SMT6 in the setup section of the Tuning Software and voila! - you are ready to re-tune the vehicle. An experienced installer can install an SMT6 unit within 30 minutes!
The SMT6 product is packaged in two kits: the SMT6 User Kit and the SMT6 Kit.
-
The SMT6 User Kit contains all the necessary items for a First Time or Once-Off installation.
The SMT6 User Kit includes the following items:
[LIST] -
SMT6 Unit with Injector Driver
-
SMT6 Harness (Wiring Loom)
-
SMT6 Communications Cable
-
SMT6 Shorting Plug (Bridging Plug)
This useful product allows you to revert your vehicle to stock standard, should you need to remove the installed SMT6 unit for any reason. -
SMT6 CD complete with all the Manuals and Software
Note: The important SMT6 Developer’s Manual is only available on the SMT6 CD. A very useful accessory to use with the SMT6 unit, is the SMT6 Test Jig. This product allows you to test the SMT6 unit and confirms that all components are working 100%. It also assists with the installation of the SMT6, as you can test for any faults at each stage of the installation. The SMT6 Test Jig is affordable and is available to purchase as an optional accessory for only 31.43 US Dollars! -
The SMT6 Kit is for a Repeat Installation. There are certain things that you won’t need to get again, as you would’ve already purchased them in the SMT6 User Kit, e.g. the SMT6 comms cable.
The useful SMT6 Shorting Plug, would need to be purchased as an additional item. The SMT6 Kit includes the following items: -
SMT6 Unit with Injector Driver
-
SMT6 Harness (Wiring Loom) [/LIST] A full list of the FEATURES AND BENEFITS of the SMT6 is included in the table below. More details on some of the important features are:
-
Lambda Feature: With the SMT6 it is possible to read the lambda sensor, as well as modify the lambda sensor signals. There are two modes of lambda tuning - linear and non-linear. The linear mode tunes according to the voltage of the sensor, while the non-linear mode allows you to tune according to a lambda value. Both tuning modes are selectable via the setup screen in the Windows Tuning Software. -
The SMT6 has an output which can be enabled according to an RPM setpoint, which is mainly used with CAM switching applications. This output can also be used to set the airflow, temperature and analog deflection points. -
The SMT6's extra injector driver allows more fuel to be added into an engine, and is ideal for Turbo applications. This extra injector driver can also be used for proportional nitrous injection. -
The SMT6 also has an input for airflow sensors and temperature sensors, and each of them has a separate map that can be used to manipulate the fuel, extra injector and ignition signals. FEATURES & BENEFITS OF THE SMT6
All piggy-back systems rely on the exiting ECU to provide the fuel and ignition to an electronically fuel injected engine. Therefore, they are also bound by the limitations of the existing ECU.
Fuel is typically modified by changing the load sensor or lambda sensor signal. Ignition is done by delaying or advancing the crank angle sensor’s signal. The piggy-back system tricks the ECU into thinking that it is running under different conditions thereby allowing for a different output.<b>Feature</b> <b>Benefit</b> Throttle Sensor learning feature Fits to any throttle position RPM Calibration To suit your installation High RPM range Ideal for racing Fuel map with 128 sites Smooth Programming Ignition Map with 128 sites Fine Ignition resolution Injection Map with 128 sites For extra (boost!) injection 0 - 10 volt Analogue range Allows tuning of most models 6 Amp injector drive Handles 6 x 16 ohm injectors Various ignition outputs For the most stringent applications Selectable Trigger points To suit your application Programmable Cylinders It works on any amount of cylinders! Selectable polarity To Suit your application Can handle interlaced signal For 4 cylinders ignition output tuning Balanced Inputs Inverted Outputs Missing Tooth Signal For up to 2 teeth advance/retard Ignition output limit Limits max. advance and retard Fuel High Low Limit Prevents overdriving the ECU Small Size Fits Anywhere Low Battery Drain Simple Installation [Self Checking Test Available](http://www.perfectpower.com/products/test_jig.asp) For Extra Confidence Map Switchable While you drive! All Inputs Protected No mishaps! Crystal Controlled For Stability Encapsulated For Moisture and Dust Easy Tuning Software DOS or WINDOWS Low Component Count High MTBF 10 MIPS computing To facilitate quick engine response Signal Conditioning To prevent miss trigger Engine profiles (library) Easy set up Lambda Signal Tuning Modification of Lambda Senor Readings Proportional Nitrous Control Less waste of power in nitrous injection Adjust Dwell Time For very basic standalone applications RPM or Airflow or Analogue Defection or Temp Switch/Set Point For CAM switch and similar applications <b>Wiring Diagrams</b> We are constantly creating NEW Wiring Diagrams for the SMT6 product, based on actual installations that we do, as well as requests that we receive. Please visit the [Downloads Section](http://www.perfectpower.com/downloads/login.asp) on our website to view the list of available Wiring Diagrams. Should you not find a diagram that you need, please email us with your specific vehicle's ECU pin out data at [EMAIL="info@perfectpower.com%20?subject=Perfect%20Power%20Website%20-%20SMT6%20Page%20Wiring%20Diagram%20Request"] info@perfectpower.com[/EMAIL] and we will create a diagram for you.