Eric's GSXR Buggy

I picked this thing up a while ago, but just started on it.

Future plans:
Full Front double A-Arm setup w/ disk brakes
Full rear double A-Arm w/ CV shafts
Racing Seat
Quick release steering wheel
Lights (even brake lights!)

Current Plans
07’ GSXR 600 engine swap
GSXR Gauges
GSXR rear caliper swap
knobby ass tires

When bought (Yes, Underboosted picked one up too!)

http://i167.photobucket.com/albums/u147/reckone518/Buggy/car5.jpg

Old Honda 13hp engine

New GSXR 600 Engine
http://i167.photobucket.com/albums/u147/reckone518/Buggy/Picture009.jpg

Pulled the engine, and trans today.
http://i167.photobucket.com/albums/u147/reckone518/Buggy/Picture010.jpg

http://i167.photobucket.com/albums/u147/reckone518/Buggy/Picture011.jpg

Just seeing how to fit everything.
http://i167.photobucket.com/albums/u147/reckone518/Buggy/Picture015.jpg

http://i167.photobucket.com/albums/u147/reckone518/Buggy/Picture016.jpg

http://i167.photobucket.com/albums/u147/reckone518/Buggy/Picture020.jpg

Custom exhaust needed as usual.
http://i167.photobucket.com/albums/u147/reckone518/Buggy/Picture021.jpg

http://i167.photobucket.com/albums/u147/reckone518/Buggy/Picture024.jpg

Engine lines up great with the original FNR trans.
http://i167.photobucket.com/albums/u147/reckone518/Buggy/Picture023.jpg

Trans cuts it to close to the engine. I need to do a little triming to the egine mount to fit the trans better.
http://i167.photobucket.com/albums/u147/reckone518/Buggy/Picture019.jpg

http://i167.photobucket.com/albums/u147/reckone518/Buggy/Picture017.jpg

i would like to drive this sir. that is all.

Dude ur nuts and can’t wait to see it done!

My friend Dom (welder for synapse) is doing somthing very similar to this, with the same motor. Good luck, should be a ton of fun

Ha ha good work dude

YESSSS. I am very jellous! I have some sick ass plans in my head for a road maybelegal one myself.

Dude if you want to jump this thing over anything more than a curb. Get yourself some long travel ATV shocks. Elka, PEP, FOX, AXIS… I know a YFZ LT setup is a 18.5" long one, but I have seen them 20"+ They can be valved to any weight, and you can just cut off the stock front end arm tabs and weld some new ones in to hold an entire ATV long travel front end on. Use the disk brakes, hubs spindles, wheels, tires, tie rods will need to be custom. but that shit would give you about 15"s of SICK ASS travel! then do something in the ass end… and you would have a mini sand rail!

sub-fucking-scribed!!!

Exactly what I planed to do already. I was going to pick up a Raptor/ Banshee front end, extend them a bit and call it good.

Going for this setup pretty much.

http://i167.photobucket.com/albums/u147/reckone518/Buggy/buggy25203.jpg

^^^^cant see^^^

:thumbup

SICK!

subscribed

Fixed :thumbup

Fukin cool.

sickkkk dude!

This looks awesome!!!

this thing looks like its gonna be nuts! so sick!

awesome!!!

Pssshhhh. GSXR 600 is weak. R1 motor would have been the win!!!

Sick dude! Looks like a great frame to start from.

Fn sick.

What are you doing for tranny/clutch?